Guangzhou, China ISO 9001 · ISO 14001 · ISO 18001 CE / GS tested by TÜV Rheinland
Sales desk Guangzhou · +86 198 6588 7686
All equipment families257 modelsBuying guides13ForkliftDiesel forklift trucks9Electric forklift trucks11LPG and gas forklift trucks7StackerReach stackers10Stackers and order pickers33Pallet truckPallet trucks25Lift table and drum handlingDrum handlers11Lift tables20Vacuum lifterVacuum lifters19Aerial work platformAerial work platforms14Electric tractorElectric tow tractors9ConveyorConveyors9Loading rampDock ramps7Storage systemStorage systems28Other handling equipmentSpecial-purpose handling equipment45 Videos Buying guides Search models Certificates Buyer FAQ About us Contact us Request a quote

Vacuum lifter selection guide

A vacuum lifter is chosen by the surface it must hold, not only by the weight it must lift.

Start with the surface

Vacuum holding depends on a seal. Smooth, non-porous surfaces — glass, polished steel, coated panel, plastic sheet — hold well. Porous or textured surfaces — concrete, unpolished stone, cardboard, some timber — leak air and need more pad area, more vacuum flow or a different attachment.

Tell the supplier what the surface actually is. 'Sheet metal' covers oily, pickled, galvanised and coated steel, and each behaves differently under a pad.

Pad area and weight

Usable lifting force comes from pad area times vacuum level, with a safety factor for acceleration, rotation and wind if the load is handled outdoors. A large thin panel also needs pads spread wide enough to stop the sheet from flexing out of the seal.

For long panels, check the deflection between pads: too few pads and the sheet bends, breaks the seal and drops.

Vacuum source

  • Electric pump — constant vacuum, suits high duty cycles and heavier loads.
  • Venturi (compressed air) — light and simple, needs a reliable compressed-air supply.
  • Battery unit — no hose to the crane, suits intermittent use and site work.

Mounting and handling pattern

Crane-suspended lifters suit vertical lifts and rotation; mast-mounted models suit repeat placement into a machine or a rack; mobile floor units with a mast suit sheet stock in a cutting area.

Rotation, tilt and side-shift change the load's centre of gravity, so the machine's rating must be read together with the attachment, not separately.

What to send

  • Material and surface finish
  • Sheet size, thickness and weight per sheet
  • Highest and lowest placement height
  • Indoor or outdoor, and any wind exposure
  • Crane capacity or the machine the lifter will mount on
  • Cycle rate per shift

Models

Models in this class

Published figures for the first 8 models of this family; open a model page for the full specification.

Vacuum lifter selection guide model comparison

ModelCapacityLiftPowerTypical use
WS-GR———Board and panel placement
WCR-GR———Panel feeding to machines
DOOR———Stone and panel handling
Aluminum mast vacuum lifter———Metal sheet lifting
Counterbalance tpye vacuum lifter———Panel feeding to machines
BS-GR-40—1200—Panel feeding to machines
WCE-GR———Panel feeding to machines
All models in this family →

Questions

Questions buyers ask

Can a vacuum lifter handle cardboard boxes?+

Only with the right pad type and enough vacuum flow; porous surfaces leak air and standard pads may not hold. State the material so the pad and pump can be sized.

Is a vacuum lifter safer than a clamp for glass?+

Neither replaces procedure. A vacuum lifter needs a vacuum gauge, a non-return valve and a check before every lift; a clamp needs the right clamping force for the thickness.

What is the lead time?+

Ready stock covers many models; customised units are built in about 25 days.

Send the load and the working conditions

Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.

Tel0086-20-23357922
WhatsApp / WeChat0086-19865887686
OfficeRoom 2102, No.348 Tancun Road, Tianhe District, Guangzhou, China
We reply within 12 working hours.