WCE-GR Vacuum lifter. Glass, stone, metal sheet and plasterboard are handled with pad frames.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.


WCE-GR Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Panel feeding to machines
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Pads are matched to the sheet surface and the load weight.
Pads are matched to the sheet surface and the load weight.
Pads are matched to the sheet surface and the load weight.
State any attachment required alongside the base model. Confirm the aisle width against the pallet depth before choosing a chassis.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Rated figures apply at the standard load centre unless a row says otherwise.
Each row in the table keeps the label and value from the source record.
Units are copied as published; convert them only when comparing models.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
Door and beam heights decide which mast will clear the route.
Note any attachment that changes the load centre or the overall width.
List the models that clear each constraint before asking for a quote.
Check the chassis width against the aisle and the container door.
Match the power arrangement to the shifts and the working environment.
On the WCE-GR, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
Mark the stations where loads are picked up and dropped off each shift.
On the WCE-GR, measure the pallet footprint and the heaviest single load before comparing models.
Keep the charging or refuelling position clear of the main traffic aisle.
On the WCE-GR, note any slope, threshold or step along the working route.
On the WCE-GR, attachments are secured before the machine leaves the station.
Unusual noise or movement is reported before further use.
On the WCE-GR, the operator follows the rated capacity marked on the chassis.
Routine checks cover tyres, brakes, controls and visible leaks.
On the WCE-GR, the layout drawing shows where each machine sits in the operation.
The receiving side pairs it with a dock ramp or platform where needed.
On the WCE-GR, attachments such as clamps or rotators are matched to the load shape.
A mixed enquiry can list this model together with other families.
On the WCE-GR, attachments are quoted separately once the base chassis is fixed.
Any option not listed should be confirmed in writing before order.
On the WCE-GR, capacity above the rated lift height follows the mast curve.
The signed datasheet issued with the quotation is the binding version.
On the WCE-GR, quotations follow the model, listed specification and destination port.
Quote the serial number and component name when ordering spares.
On the WCE-GR, the operation and parts material travel with the machine.
Mixed equipment can be listed on one enquiry.
The operation material covers controls, checks and routine service points.
Ask for the specific certificate required for your target country.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.