WCR-GR Vacuum lifter. Glass, stone, metal sheet and plasterboard are handled with pad frames.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.




WCR-GR Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Panel feeding to machines
Rotation and tilting let one operator place a panel into a rack.
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Glass, stone, metal sheet and plasterboard are handled with pad frames.
Glass, stone, metal sheet and plasterboard are handled with pad frames.
State any attachment required alongside the base model. Check closed mast or chassis height against the lowest door on the route.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Each row in the table keeps the label and value from the source record.
Units are copied as published; convert them only when comparing models.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Send pallet size, door height and aisle width with the enquiry.
Note any attachment that changes the load centre or the overall width.
Review the tyre type against the surface the machine will run on.
Match the power arrangement to the shifts and the working environment.
Compare the lowered height against the lowest door on the route.
On the WCR-GR, measure the pallet footprint and the heaviest single load before comparing models.
Check the lowest door, beam height and aisle the truck has to pass through.
On the WCR-GR, list the attachments required, such as clamps, sideshift or rotator.
State the shifts per day so the power arrangement can be sized properly.
On the WCR-GR, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the WCR-GR, attachments are secured before the machine leaves the station.
Loads are kept low while travelling between stations.
On the WCR-GR, unusual noise or movement is reported before further use.
Battery or fuel levels are checked at the start of each shift.
On the WCR-GR, a mixed enquiry can list this model together with other families.
The layout drawing shows where each machine sits in the operation.
On the WCR-GR, the receiving side pairs it with a dock ramp or platform where needed.
Spare parts for wear items follow the parts manual after delivery.
On the WCR-GR, site conditions such as gradient, dust and moisture belong in the enquiry.
Attachments are quoted separately once the base chassis is fixed.
On the WCR-GR, any option not listed should be confirmed in writing before order.
The specification sheet is the binding reference for listed values.
On the WCR-GR, wear parts are supplied after delivery against the parts manual.
Loading is recorded before the container is sealed.
On the WCR-GR, quote the serial number and component name when ordering spares.
The operation and parts material travel with the machine.
Ask for the specific certificate required for your target country.
The parts manual lists the wear items and their reference views.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.