Aluminum mast vacuum lifter Vacuum lifter. Seal condition is checked before each lift on a smooth surface.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.


Aluminum mast vacuum lifter Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Metal sheet lifting
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Describe the shifts per day when the power arrangement is selected. Check closed mast or chassis height against the lowest door on the route.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
Units are copied as published; convert them only when comparing models.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
Door and beam heights decide which mast will clear the route.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
Note any attachment that changes the load centre or the overall width.
Compare the lowered height against the lowest door on the route.
On the Aluminum mast vacuum lifter, keep the charging or refuelling position clear of the main traffic aisle.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the Aluminum mast vacuum lifter, mark the stations where loads are picked up and dropped off each shift.
Measure the pallet footprint and the heaviest single load before comparing models.
On the Aluminum mast vacuum lifter, check headroom under beams, pipes and door frames along the route.
On the Aluminum mast vacuum lifter, unusual noise or movement is reported before further use.
The operator follows the rated capacity marked on the chassis.
On the Aluminum mast vacuum lifter, the operator checks load stability before each lift or move.
Loads are kept low while travelling between stations.
On the Aluminum mast vacuum lifter, the receiving side pairs it with a dock ramp or platform where needed.
Attachments such as clamps or rotators are matched to the load shape.
On the Aluminum mast vacuum lifter, storage cages and racking organise the loads it moves between stations.
Spare parts for wear items follow the parts manual after delivery.
On the Aluminum mast vacuum lifter, any option not listed should be confirmed in writing before order.
Capacity above the rated lift height follows the mast curve.
On the Aluminum mast vacuum lifter, attachments are quoted separately once the base chassis is fixed.
Dimensions are checked against the source record before quoting.
On the Aluminum mast vacuum lifter, loading is recorded before the container is sealed.
The operation and parts material travel with the machine.
On the Aluminum mast vacuum lifter, the booking reference is issued with the proforma invoice.
Mixed equipment can be listed on one enquiry.
Test and conformity documents follow the model and destination market.
The serial number identifies the build when parts are ordered later.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.