Counterbalance tpye vacuum lifter Vacuum lifter. Glass, stone, metal sheet and plasterboard are handled with pad frames.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.


Counterbalance tpye vacuum lifter Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Panel feeding to machines
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
Seal condition is checked before each lift on a smooth surface.
Pads are matched to the sheet surface and the load weight.
Seal condition is checked before each lift on a smooth surface.
Check closed mast or chassis height against the lowest door on the route. Note cold store, outdoor gradient or container entry as a constraint.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
An em dash marks a value the source record did not publish.
Rated figures apply at the standard load centre unless a row says otherwise.
Units are copied as published; convert them only when comparing models.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
Dimensions in the table come from the source record.
Compare the lowered height against the lowest door on the route.
Note any attachment that changes the load centre or the overall width.
Match the power arrangement to the shifts and the working environment.
Check the machine weight against floor loading where the site is raised.
On the Counterbalance tpye vacuum lifter, note any slope, threshold or step along the working route.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the Counterbalance tpye vacuum lifter, list the attachments required, such as clamps, sideshift or rotator.
Mark the stations where loads are picked up and dropped off each shift.
On the Counterbalance tpye vacuum lifter, measure the pallet footprint and the heaviest single load before comparing models.
On the Counterbalance tpye vacuum lifter, routine checks cover tyres, brakes, controls and visible leaks.
Loads are kept low while travelling between stations.
On the Counterbalance tpye vacuum lifter, attachments are secured before the machine leaves the station.
The operator checks load stability before each lift or move.
On the Counterbalance tpye vacuum lifter, a mixed enquiry can list this model together with other families.
The receiving side pairs it with a dock ramp or platform where needed.
On the Counterbalance tpye vacuum lifter, this machine usually works alongside pallet trucks and stacking equipment.
Related models in the same group are listed on the family page.
On the Counterbalance tpye vacuum lifter, site conditions such as gradient, dust and moisture belong in the enquiry.
The signed datasheet issued with the quotation is the binding version.
On the Counterbalance tpye vacuum lifter, any option not listed should be confirmed in writing before order.
The specification sheet is the binding reference for listed values.
On the Counterbalance tpye vacuum lifter, the operation and parts material travel with the machine.
Packing follows sea-freight practice for the chosen chassis.
On the Counterbalance tpye vacuum lifter, wear parts are supplied after delivery against the parts manual.
The booking reference is issued with the proforma invoice.
The parts manual lists the wear items and their reference views.
Ask for the specific certificate required for your target country.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.