DOOR Vacuum lifter. Pads are matched to the sheet surface and the load weight.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.


DOOR Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Stone and panel handling
Glass, stone, metal sheet and plasterboard are handled with pad frames.
Rotation and tilting let one operator place a panel into a rack.
Rotation and tilting let one operator place a panel into a rack.
Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.
State any attachment required alongside the base model. Describe the shifts per day when the power arrangement is selected.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Options and attachments are listed separately from the base chassis.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
Dimensions in the table come from the source record.
Measure the pallet footprint before the chassis is shortlisted.
Check the chassis width against the aisle and the container door.
Check the machine weight against floor loading where the site is raised.
List the models that clear each constraint before asking for a quote.
Review the tyre type against the surface the machine will run on.
On the DOOR, state the shifts per day so the power arrangement can be sized properly.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the DOOR, mark the stations where loads are picked up and dropped off each shift.
Check headroom under beams, pipes and door frames along the route.
On the DOOR, check the lowest door, beam height and aisle the truck has to pass through.
On the DOOR, routine checks cover tyres, brakes, controls and visible leaks.
Unusual noise or movement is reported before further use.
On the DOOR, loads are kept low while travelling between stations.
The operator checks load stability before each lift or move.
On the DOOR, a mixed enquiry can list this model together with other families.
Spare parts for wear items follow the parts manual after delivery.
On the DOOR, attachments such as clamps or rotators are matched to the load shape.
The layout drawing shows where each machine sits in the operation.
On the DOOR, any option not listed should be confirmed in writing before order.
Attachments are quoted separately once the base chassis is fixed.
On the DOOR, the specification sheet is the binding reference for listed values.
Dimensions are checked against the source record before quoting.
On the DOOR, documents issued for an order are listed in the quotation.
Loading is recorded before the container is sealed.
On the DOOR, wear parts are supplied after delivery against the parts manual.
Mixed equipment can be listed on one enquiry.
Test and conformity documents follow the model and destination market.
The operation material covers controls, checks and routine service points.
The serial number identifies the build when parts are ordered later.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.