Counter balance type vacuum lifter for Cement board Vacuum lifter. Vacuum lifters grip smooth sheets by suction pad, without hooks or slings.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Counter balance type vacuum lifter for Cement board Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Metal sheet lifting
Rotation and tilting let one operator place a panel into a rack.
The lifter pairs with a crane, forklift attachment or its own battery frame.
Rotation and tilting let one operator place a panel into a rack.
The lifter pairs with a crane, forklift attachment or its own battery frame.
State any attachment required alongside the base model. Check closed mast or chassis height against the lowest door on the route.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Rated figures apply at the standard load centre unless a row says otherwise.
Each row in the table keeps the label and value from the source record.
Units are copied as published; convert them only when comparing models.
Configuration follows the load, working height and site layout.
The enquiry should list any attachment the job requires.
Measure the pallet footprint before the chassis is shortlisted.
Check the chassis width against the aisle and the container door.
List the models that clear each constraint before asking for a quote.
Match the power arrangement to the shifts and the working environment.
Compare capacity first, then the lift height the job actually needs.
On the Counter balance type vacuum lifter for Cement board, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
List the attachments required, such as clamps, sideshift or rotator.
On the Counter balance type vacuum lifter for Cement board, send photographs of the racking and the existing working area when possible.
Check headroom under beams, pipes and door frames along the route.
On the Counter balance type vacuum lifter for Cement board, mark the stations where loads are picked up and dropped off each shift.
On the Counter balance type vacuum lifter for Cement board, unusual noise or movement is reported before further use.
The working area is kept clear of loose packaging and obstacles.
On the Counter balance type vacuum lifter for Cement board, battery or fuel levels are checked at the start of each shift.
The operator checks load stability before each lift or move.
On the Counter balance type vacuum lifter for Cement board, this machine usually works alongside pallet trucks and stacking equipment.
Spare parts for wear items follow the parts manual after delivery.
On the Counter balance type vacuum lifter for Cement board, related models in the same group are listed on the family page.
Storage cages and racking organise the loads it moves between stations.
On the Counter balance type vacuum lifter for Cement board, attachments are quoted separately once the base chassis is fixed.
Capacity above the rated lift height follows the mast curve.
On the Counter balance type vacuum lifter for Cement board, site conditions such as gradient, dust and moisture belong in the enquiry.
Dimensions are checked against the source record before quoting.
On the Counter balance type vacuum lifter for Cement board, loading is recorded before the container is sealed.
Quote the serial number and component name when ordering spares.
On the Counter balance type vacuum lifter for Cement board, the enquiry should include the quantity and destination port.
Documents issued for an order are listed in the quotation.
The operation material covers controls, checks and routine service points.
Test and conformity documents follow the model and destination market.
Ask for the specific certificate required for your target country.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.