Guangzhou, China ISO 9001 · ISO 14001 · ISO 18001 CE / GS tested by TÜV Rheinland
Sales desk Guangzhou · +86 198 6588 7686
All equipment families257 modelsBuying guides13ForkliftDiesel forklift trucks9Electric forklift trucks11LPG and gas forklift trucks7StackerReach stackers10Stackers and order pickers33Pallet truckPallet trucks25Lift table and drum handlingDrum handlers11Lift tables20Vacuum lifterVacuum lifters19Aerial work platformAerial work platforms14Electric tractorElectric tow tractors9ConveyorConveyors9Loading rampDock ramps7Storage systemStorage systems28Other handling equipmentSpecial-purpose handling equipment45 Videos Buying guides Search models Certificates Buyer FAQ About us Contact us Request a quote

FD30 FD35 — diesel counterbalance forklift

FD30 FD35 Diesel Forklift, lift height 3000 mm. Diesel power suits slopes and surfaces where an indoor truck would struggle.

FD30 FD35 diesel counterbalance forklift — product photo 1 of 2
Why buyers pick this class Full specification →

Ordering facts for the FD30 FD35

Confirmed terms
Minimum order
1 set — mixed models can be combined in one container.
Lead time
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days.
Payment
T/T 30% deposit, 70% balance against copy of the bill of lading.
Loading ports
Guangzhou, Shenzhen or Nansha.
Certification
CE on the product range; the factory holds ISO 9001, ISO 14001 and ISO 18001.
Warranty
12 months from delivery.
Price
Prices are not published on this site — every offer is quoted line by line against the load, lift height, floor condition and destination port.

Specification

FD30 FD35 specification

Values are copied from the source record in their original order and units.

FD30 FD35 specification table
ParameterValue
ModelFD30 / FD35
Power TypeDiesel
Load Capacity3000 / 3500 kg
Load centre500 mm
TyrePneumatic Tyre
Front Tyre28*9-15-12PR
Rear Tyre6.50-10-10PR
Lift Height3000 mm
Fork SizeL×W×T / mm / 1070*125*45 / 1070*125*50
Mast Tilt Angle6/12
Mast Lowered Height2115 mm
Mast Extended Height4175 / 4150 mm
Length to face of fork2710 / 2750 mm
Overall Width1225 mm
Overhead Guard Height2090 mm
Travel Speed19
Lifting Speed440 / 420
ItemManufacture / C/O / Model / No.of Cylinder / Displacement(CC) / Rated Output/r.p.m(kw) / Rated Torque/r.p.m(N.m) / Bore*Stroke
1ISUZU / JAPAN / C240NKFC-01 / 4 / 2369 / 35.4/2500 / 137.7/1800 / 86*102
2ISUZU / JAPAN / 4JG2PE-01 / 4 / 3059 / 46/2450 / 184.7/1600-1800 / 95.4*107
3YANMAR / JAPAN / 4TNE98-BQFLC / 4 / 3318 / 42.1/2300 / 177.6-196.3/1700 / 98*110
4MITSUBISHI / JAPAN / S4S / 4 / 3331 / 35.3/2250 / 169/1700 / 94*120
5XINCHAI / CHINA / A498BPG-520 / 4 / 3170 / 45/2500 / 193/1800 / 98*105
6XINCHAI / CHINA / C490BPG-236 / 4 / 2670 / 40/2650 / 160/1800-2000 / 90*105
Request price Datasheet (print / save as PDF) Ask about fuel type

Gallery

Product photographs

All detail images published for this model.

What this model is built to do

FD30 FD35 Diesel Forklift, part of the Diesel forklift trucks line.

Counterbalance diesel forklifts for outdoor yards, construction sites and port apron loading.

Yard spotting and stacking

Published figures for this build: rated capacity 3000 / 3500 kg, lift height 3000 mm, overall width 1225 mm, tyre pneumatic tyre.

Open yards, timber stores, sites and port aprons are usual diesel duties.

A diesel chassis carries pneumatic tyres and an internal combustion unit.

Open yards, timber stores, sites and port aprons are usual diesel duties.

Diesel power suits slopes and surfaces where an indoor truck would struggle.

Check closed mast or chassis height against the lowest door on the route. Describe the shifts per day when the power arrangement is selected.

Specification walk-through

The specification sheet records Model: FD30 / FD35; Power Type: Diesel; Load Capacity (kg): 3000 / 3500 kg; Load centre (mm): 500 mm; Specification is not published in the source record; Tyre: Pneumatic Tyre.

The specification sheet records Front Tyre: 28*9-15-12PR; Rear Tyre: 6.50-10-10PR; Specification is not published in the source record; Lift Height (mm): 3000 mm; Fork Size: L×W×T / mm / 1070*125*45 / 1070*125*50; Mast Tilt Angle (f/r): 6/12.

The specification sheet records Mast Lowered Height (mm): 2115 mm; Mast Extended Height (with backrest): 4175 / 4150 mm; Length to face of fork (Without fork): 2710 / 2750 mm; Overall Width (mm): 1225 mm; Overhead Guard Height (mm): 2090 mm; Travel Speed (Empty load): 19.

The specification sheet records Lifting Speed (Full load): 440 / 420; Item: Manufacture / C/O / Model / No.of Cylinder / Displacement(CC) / Rated Output/r.p.m(kw) / Rated Torque/r.p.m(N.m) / Bore*Stroke; 1: ISUZU / JAPAN / C240NKFC-01 / 4 / 2369 / 35.4/2500 / 137.7/1800 / 86*102; 2: ISUZU / JAPAN / 4JG2PE-01 / 4 / 3059 / 46/2450 / 184.7/1600-1800 / 95.4*107; 3: YANMAR / JAPAN / 4TNE98-BQFLC / 4 / 3318 / 42.1/2300 / 177.6-196.3/1700 / 98*110; 4: MITSUBISHI / JAPAN / S4S / 4 / 3331 / 35.3/2250 / 169/1700 / 94*120.

The specification sheet records 5: XINCHAI / CHINA / A498BPG-520 / 4 / 3170 / 45/2500 / 193/1800 / 98*105; 6: XINCHAI / CHINA / C490BPG-236 / 4 / 2670 / 40/2650 / 160/1800-2000 / 90*105.

An em dash marks a value the source record did not publish.

Each row in the table keeps the label and value from the source record.

Those missing values can be requested directly through the enquiry form.

Options and attachments are listed separately from the base chassis.

How to specify the right build

For an internal combustion chassis, engine, tyre type and mast move the price most.

Measure the pallet footprint before the chassis is shortlisted.

Dimensions in the table come from the source record.

Compare the lowered height against the lowest door on the route.

Match the power arrangement to the shifts and the working environment.

Check the chassis width against the aisle and the container door.

List the models that clear each constraint before asking for a quote.

  • List the load per move, lift height and floor surface before comparing models.
  • Send those figures with the model code; the reply confirms whether the chassis suits.
  • Note any constraint: low door, narrow aisle, cold store, outdoor gradient or entry.

Site preparation and operating notes

On the FD30 FD35, list the attachments required, such as clamps, sideshift or rotator.

Keep the charging or refuelling position clear of the main traffic aisle.

On the FD30 FD35, state the shifts per day so the power arrangement can be sized properly.

Mark the stations where loads are picked up and dropped off each shift.

On the FD30 FD35, measure the pallet footprint and the heaviest single load before comparing models.

Operation and routine checks

On the FD30 FD35, battery or fuel levels are checked at the start of each shift.

Loads are kept low while travelling between stations.

On the FD30 FD35, unusual noise or movement is reported before further use.

The working area is kept clear of loose packaging and obstacles.

How this model fits the operation

On the FD30 FD35, a mixed enquiry can list this model together with other families.

Spare parts for wear items follow the parts manual after delivery.

On the FD30 FD35, storage cages and racking organise the loads it moves between stations.

Attachments such as clamps or rotators are matched to the load shape.

Working conditions and honest limits

On the FD30 FD35, capacity above the rated lift height follows the mast curve.

Attachments are quoted separately once the base chassis is fixed.

On the FD30 FD35, dimensions are checked against the source record before quoting.

Site conditions such as gradient, dust and moisture belong in the enquiry.

Delivery, documents and support

On the FD30 FD35, quotations follow the model, listed specification and destination port.

Mixed equipment can be listed on one enquiry.

On the FD30 FD35, the operation and parts material travel with the machine.

Documents issued for an order are listed in the quotation.

The serial number identifies the build when parts are ordered later.

Test and conformity documents follow the model and destination market.

Ask for the specific certificate required for your target country.

Before you order

  • Compare the published capacity against the heaviest single move before the mast or attachment is chosen.
  • Check overall width and turning space against the aisle and any narrow doorway before the chassis is shortlisted.
  • Any clamp, sideshift or rotator changes the load centre and must be listed alongside the base model.
  • Documents issued with the order: ISO 9001, ISO 14001 and ISO 18001 factory certificates, plus CE or GS where the model carries it, and the serial list for the shipment.
  • Wear parts are ordered after delivery against the parts manual, the serial number and the component name.

Questions

Questions buyers ask before ordering

What lift height is available?+

The specification sheet lists 3000 mm for this build. Send the rack beam and door heights together to size the mast.

What power unit does it use?+

The listed power arrangement is Diesel. Confirm the supply voltage or fuel type for your site before ordering.

Which tyres are fitted?+

The listed tyre type is Pneumatic Tyre. Solid tyres suit sealed concrete; pneumatic tyres suit rough outdoor ground.

What load centre applies to the rating?+

The specification lists a load centre of 500 mm. Loads carried farther forward reduce rated capacity.

Can it enter a container or trailer?+

Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.

Which certifications accompany the machine?+

The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.

What is the lead time?+

Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.

How are spare parts handled after delivery?+

The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.

What information do you need for a quotation?+

Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.

Related

Other models in this family

Same-family comparison using the published source figures; open a model page for the full specification.

Diesel forklift trucks related models

ModelCapacityLiftPowerTypical use
LG50—3000 mmDieselOutdoor yard loading
FD20—3000 mm—Construction and site duties
LG45—3000 mmDieselYard spotting and stacking
LG80—3000 mmDieselTimber and bulk stores
CPCD35———Outdoor yard loading

Explore

Related equipment and buying guides

Send the load and the working conditions

Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.

Tel0086-20-23357922
WhatsApp / WeChat0086-19865887686
OfficeRoom 2102, No.348 Tancun Road, Tianhe District, Guangzhou, China
We reply within 12 working hours.