FD20 FD25 Diesel Forklift, lift height 3000 mm. This class is specified for outdoor work and standing dust.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | FD 20 / FD25 |
| Rated Capacity | 2000 / 2500 kg |
| Load Center | 500 mm |
| Sta. Free Lift | 140 mm |
| Sta. Lift Height | 3000 mm |
| Lifting Speed | Unload / mm/s / 530 |
| Loaded | 500 |
| Lowering Speed | Loaded / mm/s / < 600 |
| Tilting Angle | Front/Rear / degree / 6/12 |
| Travel Speed | Loaded / km/h / 21 |
| Unloaded | 22 |
| Turning Radius | 2265 / 2310 mm |
| Length | 3410 / 3590 mm |
| Width | 1150 mm |
| Mast Height .Lowered | 2012 mm |
| Mast Height.Extended | 3935 mm |
| Height.overhead guard | 2079 mm |
| Service Weight | 3270 / 3580 kg |
| Tire Size | Front / 7.00-12-12PR |
| Rear | 6.00-9-10PR |
| Model | Make / Rated output KW / Max. Torque Nm@min-1 / Fuel Tank Capacity Ltr |
| 490BPG | xinchang / 37 / 148/1700 / 55 |
| A490BPG | xinchang / 37 / 148/1700 / 55 |
| NC493G | ISUZU / 39 / 165/1800 / 55 |
| C240PKJ | ISUZU / 37 / 162/1800 / 55 |
Gallery
All detail images published for this model.



FD20 FD25 Diesel Forklift, part of the Diesel forklift trucks line.
Counterbalance diesel forklifts for outdoor yards, construction sites and port apron loading.
Construction and site duties
Published figures for this build: rated capacity 2000 / 2500 kg, lift height 3000 mm, turning radius 2265 / 2310 mm.
Open yards, timber stores, sites and port aprons are usual diesel duties.
A diesel chassis carries pneumatic tyres and an internal combustion unit.
This class is specified for outdoor work and standing dust.
Diesel counterbalance trucks suit gravel, asphalt or packed earth.
Confirm the charger voltage or fuel type for your destination country. Compare rated capacity against the heaviest single load you move.
The specification sheet records Model: FD 20 / FD25; Rated Capacity (kg): 2000 / 2500 kg; Load Center (mm): 500 mm; Sta. Free Lift (mm): 140 mm; Sta. Lift Height (mm): 3000 mm; Lifting Speed: Unload / mm/s / 530.
The specification sheet records Loaded (mm/s): 500; Lowering Speed: Loaded / mm/s / < 600; Tilting Angle: Front/Rear / degree / 6/12; Travel Speed (FWD): Loaded / km/h / 21; Unloaded (km/h): 22; Turning Radius (mm): 2265 / 2310 mm.
The specification sheet records Length (mm): 3410 / 3590 mm; Width (mm): 1150 mm; Mast Height .Lowered (mm): 2012 mm; Mast Height.Extended (mm): 3935 mm; Height.overhead guard (mm): 2079 mm; Service Weight (kg): 3270 / 3580 kg.
The specification sheet records Tire Size: Front / 7.00-12-12PR; Rear: 6.00-9-10PR; Model: Make / Rated output KW / Max. Torque Nm@min-1 / Fuel Tank Capacity Ltr; 490BPG: xinchang / 37 / 148/1700 / 55; A490BPG: xinchang / 37 / 148/1700 / 55; NC493G: ISUZU / 39 / 165/1800 / 55.
The specification sheet records C240PKJ: ISUZU / 37 / 162/1800 / 55.
Each row in the table keeps the label and value from the source record.
Options and attachments are listed separately from the base chassis.
An em dash marks a value the source record did not publish.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
The enquiry should list any attachment the job requires.
Compare the lowered height against the lowest door on the route.
Check the machine weight against floor loading where the site is raised.
Note any attachment that changes the load centre or the overall width.
Compare capacity first, then the lift height the job actually needs.
On the FD20 FD25, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
Measure the pallet footprint and the heaviest single load before comparing models.
On the FD20 FD25, state the shifts per day so the power arrangement can be sized properly.
Mark the stations where loads are picked up and dropped off each shift.
On the FD20 FD25, check the lowest door, beam height and aisle the truck has to pass through.
On the FD20 FD25, attachments are secured before the machine leaves the station.
Battery or fuel levels are checked at the start of each shift.
On the FD20 FD25, routine checks cover tyres, brakes, controls and visible leaks.
The working area is kept clear of loose packaging and obstacles.
On the FD20 FD25, a mixed enquiry can list this model together with other families.
Attachments such as clamps or rotators are matched to the load shape.
On the FD20 FD25, storage cages and racking organise the loads it moves between stations.
This machine usually works alongside pallet trucks and stacking equipment.
On the FD20 FD25, tyre choice should match the floor rather than the price list.
Dimensions are checked against the source record before quoting.
On the FD20 FD25, the signed datasheet issued with the quotation is the binding version.
Capacity above the rated lift height follows the mast curve.
On the FD20 FD25, quotations follow the model, listed specification and destination port.
Packing follows sea-freight practice for the chosen chassis.
On the FD20 FD25, the enquiry should include the quantity and destination port.
Mixed equipment can be listed on one enquiry.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
The operation material covers controls, checks and routine service points.
Questions
The specification sheet lists 3000 mm for this build. Send the rack beam and door heights together to size the mast.
The listed tyre type is Front. Solid tyres suit sealed concrete; pneumatic tyres suit rough outdoor ground.
The specification lists a load centre of 500 mm. Loads carried farther forward reduce rated capacity.
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.