Warehouse truck WT02 Warehouse truck WT02. Pallet trucks move palletised loads across a floor or into a container.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Warehouse truck WT02 Warehouse truck WT02, part of the Pallet trucks line.
Hand, semi-electric and powered pallet trucks for horizontal pallet transport.
Warehouse replenishment
The chassis stays low, so forks slide under a standard pallet.
The chassis stays low, so forks slide under a standard pallet.
Pallet trucks move palletised loads across a floor or into a container.
Hand versions keep a simple hydraulic pump for short repeated moves.
Describe the shifts per day when the power arrangement is selected. Compare rated capacity against the heaviest single load you move.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
An em dash marks a value the source record did not publish.
Options and attachments are listed separately from the base chassis.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Dimensions in the table come from the source record.
Measure the pallet footprint before the chassis is shortlisted.
List the models that clear each constraint before asking for a quote.
Check the machine weight against floor loading where the site is raised.
Review the tyre type against the surface the machine will run on.
Note any attachment that changes the load centre or the overall width.
On the Warehouse truck WT02, note any slope, threshold or step along the working route.
Measure the pallet footprint and the heaviest single load before comparing models.
On the Warehouse truck WT02, check the lowest door, beam height and aisle the truck has to pass through.
Mark the stations where loads are picked up and dropped off each shift.
On the Warehouse truck WT02, state the shifts per day so the power arrangement can be sized properly.
On the Warehouse truck WT02, the operator checks load stability before each lift or move.
Attachments are secured before the machine leaves the station.
On the Warehouse truck WT02, routine checks cover tyres, brakes, controls and visible leaks.
Unusual noise or movement is reported before further use.
On the Warehouse truck WT02, spare parts for wear items follow the parts manual after delivery.
Attachments such as clamps or rotators are matched to the load shape.
On the Warehouse truck WT02, the receiving side pairs it with a dock ramp or platform where needed.
The layout drawing shows where each machine sits in the operation.
On the Warehouse truck WT02, tyre choice should match the floor rather than the price list.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the Warehouse truck WT02, dimensions are checked against the source record before quoting.
The signed datasheet issued with the quotation is the binding version.
On the Warehouse truck WT02, wear parts are supplied after delivery against the parts manual.
Quote the serial number and component name when ordering spares.
On the Warehouse truck WT02, the booking reference is issued with the proforma invoice.
Documents issued for an order are listed in the quotation.
Ask for the specific certificate required for your target country.
The operation material covers controls, checks and routine service points.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.