Vacuum glass lifter New Product. Dimensions on the datasheet are checked against the site layout.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Vacuum glass lifter New Product, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
General material handling
This item belongs to the broader SUNRISE material handling catalogue.
Each build is quoted line by line once the duty cycle is confirmed.
This item belongs to the broader SUNRISE material handling catalogue.
The enquiry should describe the station the equipment works at.
Confirm the aisle width against the pallet depth before choosing a chassis. Match the tyre type to the floor surface rather than the price list.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Those missing values can be requested directly through the enquiry form.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
The listed figures follow the record; options are confirmed on the quotation.
Check the chassis width against the aisle and the container door.
Note any attachment that changes the load centre or the overall width.
Compare the lowered height against the lowest door on the route.
Review the tyre type against the surface the machine will run on.
On the Vacuum glass lifter, mark the stations where loads are picked up and dropped off each shift.
State the shifts per day so the power arrangement can be sized properly.
On the Vacuum glass lifter, note any slope, threshold or step along the working route.
Keep the charging or refuelling position clear of the main traffic aisle.
On the Vacuum glass lifter, measure the pallet footprint and the heaviest single load before comparing models.
On the Vacuum glass lifter, loads are kept low while travelling between stations.
The operator checks load stability before each lift or move.
On the Vacuum glass lifter, the working area is kept clear of loose packaging and obstacles.
Routine checks cover tyres, brakes, controls and visible leaks.
On the Vacuum glass lifter, related models in the same group are listed on the family page.
Attachments such as clamps or rotators are matched to the load shape.
On the Vacuum glass lifter, spare parts for wear items follow the parts manual after delivery.
Storage cages and racking organise the loads it moves between stations.
On the Vacuum glass lifter, the specification sheet is the binding reference for listed values.
Tyre choice should match the floor rather than the price list.
On the Vacuum glass lifter, attachments are quoted separately once the base chassis is fixed.
Dimensions are checked against the source record before quoting.
On the Vacuum glass lifter, documents issued for an order are listed in the quotation.
Quote the serial number and component name when ordering spares.
On the Vacuum glass lifter, mixed equipment can be listed on one enquiry.
Quotations follow the model, listed specification and destination port.
The serial number identifies the build when parts are ordered later.
The operation material covers controls, checks and routine service points.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.