WCR-120E/030C New Product. The enquiry should describe the station the equipment works at.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | WCR-120E/030C |
| Capacity | /300 kg(extension) |
| Drive wheel | DC24/0.7KW |
| Controller | CP2207A-5102 |
| Handle | CH-II |
| Battery | 2x12V/70Ah |
| Charger | Vst224-25 |
| Load lift speed | 35 |
| Unload drive speed | 5.5 |
| Load drive speed | 4.5 |
| Unload gradeability | 10% |
| Load gradeability | 5% |
Gallery
All detail images published for this model.

WCR-120E/030C New Product, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Site-specific lifting and moving tasks
Published figures for this build: rated capacity /300 kg(extension).
Each build is quoted line by line once the duty cycle is confirmed.
The machine is specified against the load, floor and working height.
Dimensions on the datasheet are checked against the site layout.
Each build is quoted line by line once the duty cycle is confirmed.
Check closed mast or chassis height against the lowest door on the route. State any attachment required alongside the base model.
The specification sheet records Model: WCR-120E/030C; Capacity (shrink): /300 kg(extension); Drive wheel: DC24/0.7KW; Controller: CP2207A-5102; Handle: CH-II; Battery: 2x12V/70Ah.
The specification sheet records Charger: Vst224-25; Load lift speed (mm/s): 35; Unload drive speed (km/h): 5.5; Load drive speed (km/h): 4.5; Unload gradeability: 10%; Load gradeability: 5%.
Units are copied as published; convert them only when comparing models.
Each row in the table keeps the label and value from the source record.
Options and attachments are listed separately from the base chassis.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
The enquiry should list any attachment the job requires.
The listed figures follow the record; options are confirmed on the quotation.
Compare the lowered height against the lowest door on the route.
Match the power arrangement to the shifts and the working environment.
Compare capacity first, then the lift height the job actually needs.
Review the tyre type against the surface the machine will run on.
On the WCR-120E/030C, mark the stations where loads are picked up and dropped off each shift.
List the attachments required, such as clamps, sideshift or rotator.
On the WCR-120E/030C, check headroom under beams, pipes and door frames along the route.
Send photographs of the racking and the existing working area when possible.
On the WCR-120E/030C, note any slope, threshold or step along the working route.
On the WCR-120E/030C, routine checks cover tyres, brakes, controls and visible leaks.
Battery or fuel levels are checked at the start of each shift.
On the WCR-120E/030C, the working area is kept clear of loose packaging and obstacles.
Loads are kept low while travelling between stations.
On the WCR-120E/030C, the layout drawing shows where each machine sits in the operation.
The receiving side pairs it with a dock ramp or platform where needed.
On the WCR-120E/030C, attachments such as clamps or rotators are matched to the load shape.
This machine usually works alongside pallet trucks and stacking equipment.
On the WCR-120E/030C, site conditions such as gradient, dust and moisture belong in the enquiry.
The specification sheet is the binding reference for listed values.
On the WCR-120E/030C, the signed datasheet issued with the quotation is the binding version.
Attachments are quoted separately once the base chassis is fixed.
On the WCR-120E/030C, loading is recorded before the container is sealed.
Quote the serial number and component name when ordering spares.
On the WCR-120E/030C, the enquiry should include the quantity and destination port.
Packing follows sea-freight practice for the chosen chassis.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.