WPR-10 New Product. The machine is specified against the load, floor and working height.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Truck Move | Forks Lift & Tight / Holder Lift & Tilt 90° / Holder Rotate 180° / Holder Down 90 |
| Model | WPR-10 |
| Cap. | 1000 kg |
| Fork Width | 150 mm |
| Fork Length | 880 mm |
| Lowest Height | 90 mm |
| Max.Fork Open | 1200 mm |
| Min.Fork Close | 800 mm |
| Rise Time | s / 28d |
| Down Time | 10s |
| Battery | 210A 12X2V |
| Lift Motor | DC24V /2KW |
| Driving Motor | DC24V /1.2Kw |
| Weight | 750 kg |
| Overall Size | 850X1960X1980 mm |
WPR-10 New Product, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Site-specific lifting and moving tasks
Dimensions on the datasheet are checked against the site layout.
Dimensions on the datasheet are checked against the site layout.
This item belongs to the broader SUNRISE material handling catalogue.
Each build is quoted line by line once the duty cycle is confirmed.
Note cold store, outdoor gradient or container entry as a constraint. Check closed mast or chassis height against the lowest door on the route.
The specification sheet records Truck Move: Forks Lift & Tight / Holder Lift & Tilt 90° / Holder Rotate 180° / Holder Down 90; Model: WPR-10; Cap. (kg): 1000 kg; Fork Width (mm): 150 mm; Fork Length (mm): 880 mm; Lowest Height (mm): 90 mm.
The specification sheet records Max.Fork Open (mm): 1200 mm; Min.Fork Close (mm): 800 mm; Rise Time: s / 28d; Down Time: 10s; Battery: 210A 12X2V; Lift Motor: DC24V /2KW.
The specification sheet records Driving Motor: DC24V /1.2Kw; Weight (kg): 750 kg; Overall Size (mm): 850X1960X1980 mm.
Each row in the table keeps the label and value from the source record.
An em dash marks a value the source record did not publish.
Options and attachments are listed separately from the base chassis.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
The listed figures follow the record; options are confirmed on the quotation.
Compare the lowered height against the lowest door on the route.
Check the machine weight against floor loading where the site is raised.
Compare capacity first, then the lift height the job actually needs.
Check the chassis width against the aisle and the container door.
On the WPR-10, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
Note any slope, threshold or step along the working route.
On the WPR-10, mark the stations where loads are picked up and dropped off each shift.
Check headroom under beams, pipes and door frames along the route.
On the WPR-10, keep the charging or refuelling position clear of the main traffic aisle.
On the WPR-10, the working area is kept clear of loose packaging and obstacles.
The operator follows the rated capacity marked on the chassis.
On the WPR-10, battery or fuel levels are checked at the start of each shift.
Attachments are secured before the machine leaves the station.
On the WPR-10, attachments such as clamps or rotators are matched to the load shape.
The receiving side pairs it with a dock ramp or platform where needed.
On the WPR-10, spare parts for wear items follow the parts manual after delivery.
This machine usually works alongside pallet trucks and stacking equipment.
On the WPR-10, the signed datasheet issued with the quotation is the binding version.
Any option not listed should be confirmed in writing before order.
On the WPR-10, site conditions such as gradient, dust and moisture belong in the enquiry.
Dimensions are checked against the source record before quoting.
On the WPR-10, documents issued for an order are listed in the quotation.
The enquiry should include the quantity and destination port.
On the WPR-10, wear parts are supplied after delivery against the parts manual.
Quotations follow the model, listed specification and destination port.
The parts manual lists the wear items and their reference views.
The operation material covers controls, checks and routine service points.
Ask for the specific certificate required for your target country.
Questions
The listed service or net weight is 750 kg. This matters for floor loading, ramps and container plans.
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.