TF30F 50F Hydraulic table truc. Table size matches the pallet footprint and the load per cycle.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | TF30F / TF50F |
| Load Capacity | 300 kg / 500 kg |
| Lowest Height | 420 mm |
| Max. Height | 1300 mm |
| Table Dimensions | 1000×550 mm |
| Total Length | 1360 mm |
| Length of Handle | 1000 mm |
| Net Weight | 105 / 116 kg |
TF30F 50F Hydraulic table truc, part of the Lift tables line.
Hydraulic, air-hydraulic and electric lift tables for dock feeding and work positioning.
Production cell feeding
Published figures for this build: rated capacity 300 kg / 500 kg.
Lift tables raise a pallet or work piece to a comfortable height.
They reduce bending and manual lifting at packing stations and docks.
Lowered height decides how a pallet can be driven onto the deck.
Scissor mechanisms carry the load vertically, with hydraulic or electric drive.
Note cold store, outdoor gradient or container entry as a constraint. Confirm the charger voltage or fuel type for your destination country.
The specification sheet records Model: TF30F / TF50F; Load Capacity (kg): 300 kg / 500 kg; Lowest Height (mm): 420 mm; Max. Height (mm): 1300 mm; Table Dimensions (mm): 1000×550 mm; Total Length (mm): 1360 mm.
The specification sheet records Length of Handle (mm): 1000 mm; Net Weight (kg): 105 / 116 kg.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Each row in the table keeps the label and value from the source record.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
Dimensions in the table come from the source record.
Send pallet size, door height and aisle width with the enquiry.
Note any attachment that changes the load centre or the overall width.
List the models that clear each constraint before asking for a quote.
Compare capacity first, then the lift height the job actually needs.
Check the machine weight against floor loading where the site is raised.
On the TF30F 50F, check the lowest door, beam height and aisle the truck has to pass through.
Measure the pallet footprint and the heaviest single load before comparing models.
On the TF30F 50F, check headroom under beams, pipes and door frames along the route.
Note any slope, threshold or step along the working route.
On the TF30F 50F, state the shifts per day so the power arrangement can be sized properly.
On the TF30F 50F, battery or fuel levels are checked at the start of each shift.
Routine checks cover tyres, brakes, controls and visible leaks.
On the TF30F 50F, the operator follows the rated capacity marked on the chassis.
Loads are kept low while travelling between stations.
On the TF30F 50F, spare parts for wear items follow the parts manual after delivery.
The layout drawing shows where each machine sits in the operation.
On the TF30F 50F, storage cages and racking organise the loads it moves between stations.
The receiving side pairs it with a dock ramp or platform where needed.
On the TF30F 50F, site conditions such as gradient, dust and moisture belong in the enquiry.
The specification sheet is the binding reference for listed values.
On the TF30F 50F, tyre choice should match the floor rather than the price list.
Dimensions are checked against the source record before quoting.
On the TF30F 50F, the enquiry should include the quantity and destination port.
Mixed equipment can be listed on one enquiry.
On the TF30F 50F, wear parts are supplied after delivery against the parts manual.
Quote the serial number and component name when ordering spares.
Test and conformity documents follow the model and destination market.
The operation material covers controls, checks and routine service points.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.