HT200A Hand Truck. Each build is quoted line by line once the duty cycle is confirmed.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
HT200A Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Pushed hand-truck transport
Selection starts from the load per move and the space around it.
Selection starts from the load per move and the space around it.
The machine is specified against the load, floor and working height.
Each build is quoted line by line once the duty cycle is confirmed.
Confirm the charger voltage or fuel type for your destination country. Compare rated capacity against the heaviest single load you move.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
An em dash marks a value the source record did not publish.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
Dimensions in the table come from the source record.
Check the chassis width against the aisle and the container door.
Compare the lowered height against the lowest door on the route.
Note any attachment that changes the load centre or the overall width.
Compare capacity first, then the lift height the job actually needs.
On the HT200A, check headroom under beams, pipes and door frames along the route.
Mark the stations where loads are picked up and dropped off each shift.
On the HT200A, measure the pallet footprint and the heaviest single load before comparing models.
State the shifts per day so the power arrangement can be sized properly.
On the HT200A, list the attachments required, such as clamps, sideshift or rotator.
On the HT200A, the operator follows the rated capacity marked on the chassis.
Unusual noise or movement is reported before further use.
On the HT200A, battery or fuel levels are checked at the start of each shift.
Loads are kept low while travelling between stations.
On the HT200A, a mixed enquiry can list this model together with other families.
Related models in the same group are listed on the family page.
On the HT200A, storage cages and racking organise the loads it moves between stations.
The receiving side pairs it with a dock ramp or platform where needed.
On the HT200A, the specification sheet is the binding reference for listed values.
Dimensions are checked against the source record before quoting.
On the HT200A, attachments are quoted separately once the base chassis is fixed.
Tyre choice should match the floor rather than the price list.
On the HT200A, wear parts are supplied after delivery against the parts manual.
Loading is recorded before the container is sealed.
On the HT200A, the booking reference is issued with the proforma invoice.
Quote the serial number and component name when ordering spares.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
Ask for the specific certificate required for your target country.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.