Rotators XZ*** Forklift attachment. The enquiry should describe the station the equipment works at.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | @ Load center load capacity / Installation Grade / Forklift Adapter / Overall width / Beam WidthB(mm) / Rotating torque / Speed / Weight / Omission fromET / Level of focusCGH |
| XZ17J-A1 | 1700@500 / 1-1.8t / 840 / 815 / 4000Nm @14MPa / 5.2r/min @57L/min / 180 / 128 / 68 |
| XZ22R-A1 | 2200@500 / 2-2.5t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 350 / 194 / 125 |
| XZ22J-A2 | 2200@500 / 2-2.5t / 975 / 942 / 8600Nm @14MPa / 5.2r/min @57L/min / 340 / 194 / 125 |
| XZ22J-A3 | 2200@500 / 2-2.5t / 840 / 815 / 8600Nm @14MPa / 5.2r/min @57L/min / 335 / 194 / 125 |
| XZ22J-B1 | 2200@500 / 3-3.5t / 970 / 942 / 8600Nm @14MPa / 5.2r/min @57L/min / 345 / 194 / 125 |
| XZ30R-B1 | 3000@500 / 3-3.5t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 360 / 194 / 125 |
| XZ30R-B2 | 3000@500 / 3t / 1410 / 1375 / 8600Nm @14MPa / 5.2r/min @57L/min / 380 / 194 / 125 |
| XZ30R-B3 | 3000@500 / 3t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 360 / 194 / 125 |
| XZ35J-B1 | 3500@500 / 3.5-4.5t / 1275 / 1240 / 8600Nm @14MPa / 5.2r/min @57L/min / 376 / 205 / 136 |
| XZ60J-C1 | 5400@500 / IVIV / 5-7t / 1585 / 1550 / 11000Nm @18MPa / 4.1r/min @57L/min / 565 / 228 / 139 |
| XZ60J-C2 | 5400@500 / IV/Ⅲ / 5-7t / 1100 / 1065 / 11000Nm @18MPa / 4.1r/min @57L/min / 509 / 228 / 139 |
| XZ60J-C3 | 5400@500 / IV/Ⅲ / 5-7t / 1560 / 1525 / 11000Nm @18MPa / 4.1r/min @57L/min / 565 / 228 / 139 |
| Model | Pressure value(Bar) / Flow value(Bar) |
| Least | Maximum / Rotary Action |
| Least | Recommend / Maximum |
| XZ17J | 35 / 160 / 19 / 26 / 38 |
| XZ22/30/35R | 35 / 160 / 19 / 38 / 57 |
| XZ60J | 35 / 180 / 19 / 38 / 57 |
| Model | Speed / Torque |
| XZ17J | 7.5r/min@58L/min / 4200N.m@160Bar |
| XZ22/30/35R | 5.2r/min@57L/min / 9000N.m@160Bar |
| XZ60J | 4.1r/min@57L/min / 11000N.m@160Bar |
Gallery
All detail images published for this model.





Rotators XZ*** Forklift attachment, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
General material handling
Each build is quoted line by line once the duty cycle is confirmed.
This item belongs to the broader SUNRISE material handling catalogue.
The machine is specified against the load, floor and working height.
This item belongs to the broader SUNRISE material handling catalogue.
Note cold store, outdoor gradient or container entry as a constraint. Describe the shifts per day when the power arrangement is selected.
The specification sheet records Model: @ Load center load capacity / Installation Grade / Forklift Adapter / Overall width / Beam WidthB(mm) / Rotating torque / Speed / Weight / Omission fromET / Level of focusCGH; XZ17J-A1: 1700@500 / 1-1.8t / 840 / 815 / 4000Nm @14MPa / 5.2r/min @57L/min / 180 / 128 / 68; XZ22R-A1: 2200@500 / 2-2.5t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 350 / 194 / 125; XZ22J-A2: 2200@500 / 2-2.5t / 975 / 942 / 8600Nm @14MPa / 5.2r/min @57L/min / 340 / 194 / 125; XZ22J-A3: 2200@500 / 2-2.5t / 840 / 815 / 8600Nm @14MPa / 5.2r/min @57L/min / 335 / 194 / 125; XZ22J-B1: 2200@500 / 3-3.5t / 970 / 942 / 8600Nm @14MPa / 5.2r/min @57L/min / 345 / 194 / 125.
The specification sheet records XZ30R-B1: 3000@500 / 3-3.5t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 360 / 194 / 125; XZ30R-B2: 3000@500 / 3t / 1410 / 1375 / 8600Nm @14MPa / 5.2r/min @57L/min / 380 / 194 / 125; XZ30R-B3: 3000@500 / 3t / 1180 / 1145 / 8600Nm @14MPa / 5.2r/min @57L/min / 360 / 194 / 125; XZ35J-B1: 3500@500 / 3.5-4.5t / 1275 / 1240 / 8600Nm @14MPa / 5.2r/min @57L/min / 376 / 205 / 136; XZ60J-C1: 5400@500 / IVIV / 5-7t / 1585 / 1550 / 11000Nm @18MPa / 4.1r/min @57L/min / 565 / 228 / 139; XZ60J-C2: 5400@500 / IV/Ⅲ / 5-7t / 1100 / 1065 / 11000Nm @18MPa / 4.1r/min @57L/min / 509 / 228 / 139.
The specification sheet records XZ60J-C3: 5400@500 / IV/Ⅲ / 5-7t / 1560 / 1525 / 11000Nm @18MPa / 4.1r/min @57L/min / 565 / 228 / 139; Model: Pressure value(Bar) / Flow value(Bar); Least: Maximum / Rotary Action; Least: Recommend / Maximum; XZ17J: 35 / 160 / 19 / 26 / 38; XZ22/30/35R: 35 / 160 / 19 / 38 / 57.
The specification sheet records XZ60J: 35 / 180 / 19 / 38 / 57; Model: Speed / Torque; XZ17J: 7.5r/min@58L/min / 4200N.m@160Bar; XZ22/30/35R: 5.2r/min@57L/min / 9000N.m@160Bar; XZ60J: 4.1r/min@57L/min / 11000N.m@160Bar.
Those missing values can be requested directly through the enquiry form.
An em dash marks a value the source record did not publish.
Options and attachments are listed separately from the base chassis.
Units are copied as published; convert them only when comparing models.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
Door and beam heights decide which mast will clear the route.
Review the tyre type against the surface the machine will run on.
Check the machine weight against floor loading where the site is raised.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
On the Rotators XZ***, send photographs of the racking and the existing working area when possible.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the Rotators XZ***, keep the charging or refuelling position clear of the main traffic aisle.
List the attachments required, such as clamps, sideshift or rotator.
On the Rotators XZ***, state the shifts per day so the power arrangement can be sized properly.
On the Rotators XZ***, loads are kept low while travelling between stations.
The working area is kept clear of loose packaging and obstacles.
On the Rotators XZ***, unusual noise or movement is reported before further use.
Routine checks cover tyres, brakes, controls and visible leaks.
On the Rotators XZ***, attachments such as clamps or rotators are matched to the load shape.
Related models in the same group are listed on the family page.
On the Rotators XZ***, a mixed enquiry can list this model together with other families.
Storage cages and racking organise the loads it moves between stations.
On the Rotators XZ***, attachments are quoted separately once the base chassis is fixed.
Capacity above the rated lift height follows the mast curve.
On the Rotators XZ***, dimensions are checked against the source record before quoting.
Any option not listed should be confirmed in writing before order.
On the Rotators XZ***, the operation and parts material travel with the machine.
Wear parts are supplied after delivery against the parts manual.
On the Rotators XZ***, the booking reference is issued with the proforma invoice.
The enquiry should include the quantity and destination port.
Ask for the specific certificate required for your target country.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.