SRWL*** Wire mesh container. Racking and systems organise pallet and carton positions inside a warehouse.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| SRWL-001 | 900 / 600 / 1500 / 300 / 7 / 25 / 150 |
| SRWL-002 | 1000 / 800 / 1700 / 400-500 / 7 / 25 / 150 |
| SRWL-003 | 1100 / 800 / 1700 / 400-500 / 7 / 25 / 150 |
| SRWL-004 | 1200 / 900 / 1700 / 400-500 / 7 / 25 / 150 |
| SRWL-005 | 1300 / 1000 / 1700 / 400-500 / 7 / 25 / 150 |
SRWL*** Wire mesh container, part of the Storage systems line.
Racking, wire mesh containers, pallets and decking for pallet and bulk-goods storage.
Returnable goods storage
Beam, shelving and cage layouts follow pallet size and aisle height.
Beam, shelving and cage layouts follow pallet size and aisle height.
Access floor space and column lines are checked against the design.
Load beams are spaced to the pallet depth and stacking height.
Match the tyre type to the floor surface rather than the price list. Confirm the charger voltage or fuel type for your destination country.
The specification sheet records SRWL-001: 900 / 600 / 1500 / 300 / 7 / 25 / 150; SRWL-002: 1000 / 800 / 1700 / 400-500 / 7 / 25 / 150; SRWL-003: 1100 / 800 / 1700 / 400-500 / 7 / 25 / 150; SRWL-004: 1200 / 900 / 1700 / 400-500 / 7 / 25 / 150; SRWL-005: 1300 / 1000 / 1700 / 400-500 / 7 / 25 / 150.
Remaining parameters are listed row by row in the specification table.
Units are copied as published; convert them only when comparing models.
Those missing values can be requested directly through the enquiry form.
Rated figures apply at the standard load centre unless a row says otherwise.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Door and beam heights decide which mast will clear the route.
Review the tyre type against the surface the machine will run on.
Compare the lowered height against the lowest door on the route.
Note any attachment that changes the load centre or the overall width.
Compare capacity first, then the lift height the job actually needs.
On the SRWL***, keep the charging or refuelling position clear of the main traffic aisle.
Note any slope, threshold or step along the working route.
On the SRWL***, mark the stations where loads are picked up and dropped off each shift.
Send photographs of the racking and the existing working area when possible.
On the SRWL***, state the shifts per day so the power arrangement can be sized properly.
On the SRWL***, the operator checks load stability before each lift or move.
Attachments are secured before the machine leaves the station.
On the SRWL***, the operator follows the rated capacity marked on the chassis.
Loads are kept low while travelling between stations.
On the SRWL***, the receiving side pairs it with a dock ramp or platform where needed.
Storage cages and racking organise the loads it moves between stations.
On the SRWL***, related models in the same group are listed on the family page.
This machine usually works alongside pallet trucks and stacking equipment.
On the SRWL***, capacity above the rated lift height follows the mast curve.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the SRWL***, attachments are quoted separately once the base chassis is fixed.
The specification sheet is the binding reference for listed values.
On the SRWL***, loading is recorded before the container is sealed.
Quotations follow the model, listed specification and destination port.
On the SRWL***, documents issued for an order are listed in the quotation.
Wear parts are supplied after delivery against the parts manual.
The operation material covers controls, checks and routine service points.
The serial number identifies the build when parts are ordered later.
Ask for the specific certificate required for your target country.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.