Logistic roll container LRC02 Logistic roll container LRC02. The storage layout sets the aisle width the truck must enter.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.

Logistic roll container LRC02 Logistic roll container LRC02, part of the Storage systems line.
Racking, wire mesh containers, pallets and decking for pallet and bulk-goods storage.
Carton shelving storage
Beam, shelving and cage layouts follow pallet size and aisle height.
Access floor space and column lines are checked against the design.
Racking and systems organise pallet and carton positions inside a warehouse.
Racking and systems organise pallet and carton positions inside a warehouse.
Describe the shifts per day when the power arrangement is selected. Confirm the charger voltage or fuel type for your destination country.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
An em dash marks a value the source record did not publish.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
The listed figures follow the record; options are confirmed on the quotation.
Check the machine weight against floor loading where the site is raised.
List the models that clear each constraint before asking for a quote.
Review the tyre type against the surface the machine will run on.
Note any attachment that changes the load centre or the overall width.
On the Logistic roll container LRC02, keep the charging or refuelling position clear of the main traffic aisle.
Mark the stations where loads are picked up and dropped off each shift.
On the Logistic roll container LRC02, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
List the attachments required, such as clamps, sideshift or rotator.
On the Logistic roll container LRC02, check headroom under beams, pipes and door frames along the route.
On the Logistic roll container LRC02, the operator checks load stability before each lift or move.
The working area is kept clear of loose packaging and obstacles.
On the Logistic roll container LRC02, attachments are secured before the machine leaves the station.
The operator follows the rated capacity marked on the chassis.
On the Logistic roll container LRC02, storage cages and racking organise the loads it moves between stations.
This machine usually works alongside pallet trucks and stacking equipment.
On the Logistic roll container LRC02, the receiving side pairs it with a dock ramp or platform where needed.
Attachments such as clamps or rotators are matched to the load shape.
On the Logistic roll container LRC02, attachments are quoted separately once the base chassis is fixed.
Capacity above the rated lift height follows the mast curve.
On the Logistic roll container LRC02, any option not listed should be confirmed in writing before order.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the Logistic roll container LRC02, the booking reference is issued with the proforma invoice.
Quote the serial number and component name when ordering spares.
On the Logistic roll container LRC02, documents issued for an order are listed in the quotation.
Loading is recorded before the container is sealed.
Test and conformity documents follow the model and destination market.
The serial number identifies the build when parts are ordered later.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.