FSEP3-2.7 / FSEP3-3.3 Boom lift, rated capacity 300 kg. The platform size matches the operator, tools and load carried up.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model Number | FSEP3-2.7 / FSEP3-3.3 |
| Max.Platform Height | 2700 / 3300 mm |
| Max.Machine Height | 4100 / 5000 mm |
| Ground Clearance | 40 mm |
| Lift Rated Capacity | 300 kg |
| Platform Size | 600x640 mm |
| Max.Drive Speed | 4 |
| Max.Drive Speed | 1.6 |
| Min.turning Radius | 1500 mm |
| Max.Climbing Capacity | 15~20 % |
| Driving Wheel Size | 230X80 mm |
| Caster Size | in / 6 |
| Driving Motor | 2X24/0.5 |
| Lifting Motor | 24/1.6 |
| Anerold battery | 2×12/120 |
| Charger | 24/15 |
| Overall Length | 1530 mm |
| Overall Width | 700 mm |
| Overall Height | 1830 / 2130 mm |
| Overall Net Weight | 430 / 450 kg |
Gallery
All detail images published for this model.

FSEP3-2.7 / FSEP3-3.3 Boom lift, part of the Aerial work platforms line.
Scissor, boom and vertical-mast platforms for maintenance, fit-out and installation heights.
Assembly on a platform
Published figures for this build: rated capacity 300 kg, overall width 700 mm, turning radius 1500 mm.
Maintenance, fit-out and warehousing at height are the usual jobs.
Guard rails and a platform replace climbing on racking or frames.
The platform size matches the operator, tools and load carried up.
Maintenance, fit-out and warehousing at height are the usual jobs.
Compare rated capacity against the heaviest single load you move. Confirm the charger voltage or fuel type for your destination country.
The specification sheet records Drivable at full height is not published in the source record; Non-marking tyre is not published in the source record; 2WD is not published in the source record; Artomatic brake system is not published in the source record; Emergency lowering system is not published in the source record; Emergency stop button is not published in the source record.
The specification sheet records Cylinder holding valve is not published in the source record; Onboard diagnostic system is not published in the source record; Tilt sensor with alarm is not published in the source record; All motion alarm is not published in the source record; Horn is not published in the source record; Forklift pockets is not published in the source record.
The specification sheet records Charger protection is not published in the source record; Flashing beacon is not published in the source record; Model Number: FSEP3-2.7 / FSEP3-3.3; Max.Platform Height (mm): 2700 / 3300 mm; Max.Machine Height (mm): 4100 / 5000 mm; Ground Clearance (mm): 40 mm.
The specification sheet records Lift Rated Capacity (kg): 300 kg; Platform Size (mm): 600x640 mm; Max.Drive Speed (platform Stowed): 4; Max.Drive Speed (platform Elevated): 1.6; Min.turning Radius (mm): 1500 mm; Max.Climbing Capacity (%): 15~20 %.
The specification sheet records Driving Wheel Size (mm): 230X80 mm; Caster Size: in / 6; Driving Motor (v/kw): 2X24/0.5; Lifting Motor (v/kw): 24/1.6; Anerold battery (v/ah): 2×12/120; Charger (v/a): 24/15.
The specification sheet records Overall Length (mm): 1530 mm; Overall Width (mm): 700 mm; Overall Height (mm): 1830 / 2130 mm; Overall Net Weight (kg): 430 / 450 kg.
Rated figures apply at the standard load centre unless a row says otherwise.
Those missing values can be requested directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
The listed figures follow the record; options are confirmed on the quotation.
Check the machine weight against floor loading where the site is raised.
Compare the lowered height against the lowest door on the route.
Check the chassis width against the aisle and the container door.
Match the power arrangement to the shifts and the working environment.
On the FSEP3-2.7 / FSEP3-3.3, send photographs of the racking and the existing working area when possible.
Note any slope, threshold or step along the working route.
On the FSEP3-2.7 / FSEP3-3.3, measure the pallet footprint and the heaviest single load before comparing models.
List the attachments required, such as clamps, sideshift or rotator.
On the FSEP3-2.7 / FSEP3-3.3, check headroom under beams, pipes and door frames along the route.
On the FSEP3-2.7 / FSEP3-3.3, routine checks cover tyres, brakes, controls and visible leaks.
The operator follows the rated capacity marked on the chassis.
On the FSEP3-2.7 / FSEP3-3.3, battery or fuel levels are checked at the start of each shift.
Unusual noise or movement is reported before further use.
On the FSEP3-2.7 / FSEP3-3.3, spare parts for wear items follow the parts manual after delivery.
This machine usually works alongside pallet trucks and stacking equipment.
On the FSEP3-2.7 / FSEP3-3.3, the layout drawing shows where each machine sits in the operation.
A mixed enquiry can list this model together with other families.
On the FSEP3-2.7 / FSEP3-3.3, the signed datasheet issued with the quotation is the binding version.
Tyre choice should match the floor rather than the price list.
On the FSEP3-2.7 / FSEP3-3.3, the specification sheet is the binding reference for listed values.
Dimensions are checked against the source record before quoting.
On the FSEP3-2.7 / FSEP3-3.3, the operation and parts material travel with the machine.
Documents issued for an order are listed in the quotation.
On the FSEP3-2.7 / FSEP3-3.3, the booking reference is issued with the proforma invoice.
Wear parts are supplied after delivery against the parts manual.
The operation material covers controls, checks and routine service points.
The parts manual lists the wear items and their reference views.
Test and conformity documents follow the model and destination market.
Published overall dimensions for this build are about 1.53 m long and 0.7 m wide.
On a standard 20GP dry-van floor that footprint allows about 9 unit(s) per layer; a 40HQ allows about 21 unit(s) per layer.
The count is a footprint estimate against standard dry-van internal dimensions, not a loading guarantee. Final blocking, bracing and stacking follow the loading plan confirmed before sealing, and this model can be combined with other families in one container where the floor allows.
Questions
The listed rated capacity is 300 kg at the standard load centre. Above the rated lift height capacity derates along the mast curve.
The listed turning radius is 1500 mm. Aisle width also depends on pallet depth and fork length.
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Aerial work platforms related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.