GZS70A / 70A-1 / 70B / 70C Hand Truck. This item belongs to the broader SUNRISE material handling catalogue.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.



GZS70A / 70A-1 / 70B / 70C Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Light load manual handling
Each build is quoted line by line once the duty cycle is confirmed.
Selection starts from the load per move and the space around it.
Each build is quoted line by line once the duty cycle is confirmed.
Dimensions on the datasheet are checked against the site layout.
Note cold store, outdoor gradient or container entry as a constraint. Match the tyre type to the floor surface rather than the price list.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
Rated figures apply at the standard load centre unless a row says otherwise.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Measure the pallet footprint before the chassis is shortlisted.
Review the tyre type against the surface the machine will run on.
List the models that clear each constraint before asking for a quote.
Note any attachment that changes the load centre or the overall width.
Check the machine weight against floor loading where the site is raised.
On the GZS70A / 70A-1 / 70B / 70C, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
Note any slope, threshold or step along the working route.
On the GZS70A / 70A-1 / 70B / 70C, check headroom under beams, pipes and door frames along the route.
Mark the stations where loads are picked up and dropped off each shift.
On the GZS70A / 70A-1 / 70B / 70C, send photographs of the racking and the existing working area when possible.
On the GZS70A / 70A-1 / 70B / 70C, the operator follows the rated capacity marked on the chassis.
Battery or fuel levels are checked at the start of each shift.
On the GZS70A / 70A-1 / 70B / 70C, loads are kept low while travelling between stations.
Routine checks cover tyres, brakes, controls and visible leaks.
On the GZS70A / 70A-1 / 70B / 70C, related models in the same group are listed on the family page.
Spare parts for wear items follow the parts manual after delivery.
On the GZS70A / 70A-1 / 70B / 70C, the layout drawing shows where each machine sits in the operation.
Attachments such as clamps or rotators are matched to the load shape.
On the GZS70A / 70A-1 / 70B / 70C, dimensions are checked against the source record before quoting.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the GZS70A / 70A-1 / 70B / 70C, the specification sheet is the binding reference for listed values.
The signed datasheet issued with the quotation is the binding version.
On the GZS70A / 70A-1 / 70B / 70C, the booking reference is issued with the proforma invoice.
Mixed equipment can be listed on one enquiry.
On the GZS70A / 70A-1 / 70B / 70C, the operation and parts material travel with the machine.
The enquiry should include the quantity and destination port.
Ask for the specific certificate required for your target country.
The serial number identifies the build when parts are ordered later.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.