GZS60A / 60S Hand Truck. The machine is specified against the load, floor and working height.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
GZS60A / 60S Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Hand carrying and moving loads
The enquiry should describe the station the equipment works at.
Selection starts from the load per move and the space around it.
Selection starts from the load per move and the space around it.
Selection starts from the load per move and the space around it.
Match the tyre type to the floor surface rather than the price list. State any attachment required alongside the base model.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Each row in the table keeps the label and value from the source record.
Rated figures apply at the standard load centre unless a row says otherwise.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Dimensions in the table come from the source record.
Compare capacity first, then the lift height the job actually needs.
Check the machine weight against floor loading where the site is raised.
Compare the lowered height against the lowest door on the route.
Review the tyre type against the surface the machine will run on.
On the GZS60A / 60S, check the lowest door, beam height and aisle the truck has to pass through.
Measure the pallet footprint and the heaviest single load before comparing models.
On the GZS60A / 60S, keep the charging or refuelling position clear of the main traffic aisle.
Note any slope, threshold or step along the working route.
On the GZS60A / 60S, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the GZS60A / 60S, the operator checks load stability before each lift or move.
Attachments are secured before the machine leaves the station.
On the GZS60A / 60S, routine checks cover tyres, brakes, controls and visible leaks.
Battery or fuel levels are checked at the start of each shift.
On the GZS60A / 60S, related models in the same group are listed on the family page.
The layout drawing shows where each machine sits in the operation.
On the GZS60A / 60S, storage cages and racking organise the loads it moves between stations.
A mixed enquiry can list this model together with other families.
On the GZS60A / 60S, the specification sheet is the binding reference for listed values.
Any option not listed should be confirmed in writing before order.
On the GZS60A / 60S, tyre choice should match the floor rather than the price list.
Dimensions are checked against the source record before quoting.
On the GZS60A / 60S, quote the serial number and component name when ordering spares.
Packing follows sea-freight practice for the chosen chassis.
On the GZS60A / 60S, documents issued for an order are listed in the quotation.
Mixed equipment can be listed on one enquiry.
Test and conformity documents follow the model and destination market.
Ask for the specific certificate required for your target country.
The serial number identifies the build when parts are ordered later.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.