GZS100ST / 100AT Hand Truck. The enquiry should describe the station the equipment works at.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.

GZS100ST / 100AT Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Manual trolley duties
Dimensions on the datasheet are checked against the site layout.
Each build is quoted line by line once the duty cycle is confirmed.
The machine is specified against the load, floor and working height.
Each build is quoted line by line once the duty cycle is confirmed.
State any attachment required alongside the base model. Check closed mast or chassis height against the lowest door on the route.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
Those missing values can be requested directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Send pallet size, door height and aisle width with the enquiry.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
Note any attachment that changes the load centre or the overall width.
Check the machine weight against floor loading where the site is raised.
On the GZS100ST / 100AT, check headroom under beams, pipes and door frames along the route.
Check the lowest door, beam height and aisle the truck has to pass through.
On the GZS100ST / 100AT, mark the stations where loads are picked up and dropped off each shift.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the GZS100ST / 100AT, list the attachments required, such as clamps, sideshift or rotator.
On the GZS100ST / 100AT, attachments are secured before the machine leaves the station.
Battery or fuel levels are checked at the start of each shift.
On the GZS100ST / 100AT, unusual noise or movement is reported before further use.
Routine checks cover tyres, brakes, controls and visible leaks.
On the GZS100ST / 100AT, attachments such as clamps or rotators are matched to the load shape.
Storage cages and racking organise the loads it moves between stations.
On the GZS100ST / 100AT, the receiving side pairs it with a dock ramp or platform where needed.
Related models in the same group are listed on the family page.
On the GZS100ST / 100AT, any option not listed should be confirmed in writing before order.
The specification sheet is the binding reference for listed values.
On the GZS100ST / 100AT, capacity above the rated lift height follows the mast curve.
Tyre choice should match the floor rather than the price list.
On the GZS100ST / 100AT, packing follows sea-freight practice for the chosen chassis.
Documents issued for an order are listed in the quotation.
On the GZS100ST / 100AT, loading is recorded before the container is sealed.
Wear parts are supplied after delivery against the parts manual.
Ask for the specific certificate required for your target country.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.