foldable hand trolley SRT01-4A4 foldable hand trolley SRT01-4A4. The machine is specified against the load, floor and working height.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.









foldable hand trolley SRT01-4A4 foldable hand trolley SRT01-4A4, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Light load manual handling
Dimensions on the datasheet are checked against the site layout.
Each build is quoted line by line once the duty cycle is confirmed.
Dimensions on the datasheet are checked against the site layout.
The enquiry should describe the station the equipment works at.
Note cold store, outdoor gradient or container entry as a constraint. Match the tyre type to the floor surface rather than the price list.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Options and attachments are listed separately from the base chassis.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
The enquiry should list any attachment the job requires.
Compare the lowered height against the lowest door on the route.
List the models that clear each constraint before asking for a quote.
Match the power arrangement to the shifts and the working environment.
Note any attachment that changes the load centre or the overall width.
On the foldable hand trolley SRT01-4A4, keep the charging or refuelling position clear of the main traffic aisle.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the foldable hand trolley SRT01-4A4, check headroom under beams, pipes and door frames along the route.
Check the lowest door, beam height and aisle the truck has to pass through.
On the foldable hand trolley SRT01-4A4, send photographs of the racking and the existing working area when possible.
On the foldable hand trolley SRT01-4A4, the operator checks load stability before each lift or move.
Loads are kept low while travelling between stations.
On the foldable hand trolley SRT01-4A4, routine checks cover tyres, brakes, controls and visible leaks.
The operator follows the rated capacity marked on the chassis.
On the foldable hand trolley SRT01-4A4, the layout drawing shows where each machine sits in the operation.
A mixed enquiry can list this model together with other families.
On the foldable hand trolley SRT01-4A4, this machine usually works alongside pallet trucks and stacking equipment.
The receiving side pairs it with a dock ramp or platform where needed.
On the foldable hand trolley SRT01-4A4, capacity above the rated lift height follows the mast curve.
Tyre choice should match the floor rather than the price list.
On the foldable hand trolley SRT01-4A4, attachments are quoted separately once the base chassis is fixed.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the foldable hand trolley SRT01-4A4, documents issued for an order are listed in the quotation.
The booking reference is issued with the proforma invoice.
On the foldable hand trolley SRT01-4A4, mixed equipment can be listed on one enquiry.
Wear parts are supplied after delivery against the parts manual.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
Ask for the specific certificate required for your target country.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.