electric vacuum lifter New Product. Selection starts from the load per move and the space around it.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
electric vacuum lifter New Product, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
General material handling
Selection starts from the load per move and the space around it.
Dimensions on the datasheet are checked against the site layout.
Selection starts from the load per move and the space around it.
Dimensions on the datasheet are checked against the site layout.
Compare rated capacity against the heaviest single load you move. State any attachment required alongside the base model.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Those missing values can be requested directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
Door and beam heights decide which mast will clear the route.
Match the power arrangement to the shifts and the working environment.
Check the machine weight against floor loading where the site is raised.
List the models that clear each constraint before asking for a quote.
Review the tyre type against the surface the machine will run on.
On the electric vacuum lifter, keep the charging or refuelling position clear of the main traffic aisle.
Note any slope, threshold or step along the working route.
On the electric vacuum lifter, state the shifts per day so the power arrangement can be sized properly.
Send photographs of the racking and the existing working area when possible.
On the electric vacuum lifter, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the electric vacuum lifter, the operator follows the rated capacity marked on the chassis.
Battery or fuel levels are checked at the start of each shift.
On the electric vacuum lifter, unusual noise or movement is reported before further use.
The operator checks load stability before each lift or move.
On the electric vacuum lifter, a mixed enquiry can list this model together with other families.
The receiving side pairs it with a dock ramp or platform where needed.
On the electric vacuum lifter, this machine usually works alongside pallet trucks and stacking equipment.
Related models in the same group are listed on the family page.
On the electric vacuum lifter, tyre choice should match the floor rather than the price list.
Attachments are quoted separately once the base chassis is fixed.
On the electric vacuum lifter, dimensions are checked against the source record before quoting.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the electric vacuum lifter, the operation and parts material travel with the machine.
The enquiry should include the quantity and destination port.
On the electric vacuum lifter, quotations follow the model, listed specification and destination port.
Mixed equipment can be listed on one enquiry.
The operation material covers controls, checks and routine service points.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.