Electric floor crane SDC1030-E Electric floor crane SDC1030-E. Each build is quoted line by line once the duty cycle is confirmed.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | SDC0525-E; SDC1025-E; SDC1030-E |
| Order Number | SDC0525-E: 8.05001; SDC1025-E: 8.05002; SDC1030-E: 8.05003 |
| Capacity | SDC0525-E: 500; SDC1025-E: 1000; SDC1030-E: 1000 |
| Lifting Height | SDC0525-E: 2500; SDC1025-E: 2500; SDC1030-E: 3000 |
| Battery | SDC0525-E: 24/120; SDC1025-E: 24/120; SDC1030-E: 24/120 |
| Charger | SDC0525-E: 24/15; SDC1025-E: 24/15; SDC1030-E: 24/15 |
| Lifting motor | SDC0525-E: 2.5; SDC1025-E: 2.5; SDC1030-E: 2.5 |
| Driving motor | SDC0525-E: 0.75; SDC1025-E: 1; SDC1030-E: 1 |
| Rotation | SDC0525-E: 360°; SDC1025-E: 360°; SDC1030-E: 360° |
| Arm Reach | SDC0525-E: 1900-2500; SDC1025-E: 1900-2500; SDC1030-E: 1900-2500 |
| Chassis Length | SDC0525-E: 1900; SDC1025-E: 1900; SDC1030-E: 1900 |
| Chassis Width | SDC0525-E: 1100; SDC1025-E: 1100; SDC1030-E: 1100 |
| Straddles Length | SDC0525-E: 800; SDC1025-E: 800; SDC1030-E: 800 |
| Min. Arm Extending Distance from Outriggers | SDC0525-E: 600; SDC1025-E: 600; SDC1030-E: 600 |
| Power Voltage | SDC0525-E: 380V; SDC1025-E: 380V; SDC1030-E: 380V |
| Weight | SDC0525-E: 1250; SDC1025-E: 1290; SDC1030-E: 1450 |
| Overall size (mm) L*W*H | SDC0525-E: 3300*1200*1900; SDC1025-E: 3500*1300*1900; SDC1030-E: 3700*1500*1900 |
| Turning Aisle | SDC0525-E: 3500; SDC1025-E: 3700; SDC1030-E: 3900 |
| Passing Aisle | SDC0525-E: 1500; SDC1025-E: 1600; SDC1030-E: 1800 |
| Pneumatic Tire | SDC0525-E: 4*Ø400*80; SDC1025-E: 4*Ø500*80; SDC1030-E: 4*Ø500*80 |
| Driving wheel | 1*Ø250*80 |
| Climbing slope | 4/6 |
| Travel Speed | 4/6 Loaded/Unloaded |
| Lifting Speed | 45/50 Loaded/Unloaded |
| Falling Speed | 45/40 Loaded/Unloaded |
| Service Brake | Electromagnetic braking |
Gallery
All detail images published for this model.

Electric floor crane SDC1030-E Electric floor crane SDC1030-E, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Attachment and auxiliary handling
Published figures for this build: rated capacity SDC0525-E: 500; SDC1025-E: 1000; SDC1030-E: 1000, turning radius SDC0525-E: 3500; SDC1025-E: 3700; SDC1030-E: 3900.
This item belongs to the broader SUNRISE material handling catalogue.
Selection starts from the load per move and the space around it.
Dimensions on the datasheet are checked against the site layout.
The machine is specified against the load, floor and working height.
Note cold store, outdoor gradient or container entry as a constraint. Describe the shifts per day when the power arrangement is selected.
The specification sheet records Model: SDC0525-E; SDC1025-E; SDC1030-E; Order Number: SDC0525-E: 8.05001; SDC1025-E: 8.05002; SDC1030-E: 8.05003; Capacity (kg): SDC0525-E: 500; SDC1025-E: 1000; SDC1030-E: 1000; Lifting Height (mm): SDC0525-E: 2500; SDC1025-E: 2500; SDC1030-E: 3000; Battery (V/Ah): SDC0525-E: 24/120; SDC1025-E: 24/120; SDC1030-E: 24/120; Charger (V/A): SDC0525-E: 24/15; SDC1025-E: 24/15; SDC1030-E: 24/15.
The specification sheet records Lifting motor (Kw): SDC0525-E: 2.5; SDC1025-E: 2.5; SDC1030-E: 2.5; Driving motor (Kw): SDC0525-E: 0.75; SDC1025-E: 1; SDC1030-E: 1; Rotation (°): SDC0525-E: 360°; SDC1025-E: 360°; SDC1030-E: 360°; Arm Reach (mm): SDC0525-E: 1900-2500; SDC1025-E: 1900-2500; SDC1030-E: 1900-2500; Chassis Length (mm): SDC0525-E: 1900; SDC1025-E: 1900; SDC1030-E: 1900; Chassis Width (mm): SDC0525-E: 1100; SDC1025-E: 1100; SDC1030-E: 1100.
The specification sheet records Straddles Length (mm): SDC0525-E: 800; SDC1025-E: 800; SDC1030-E: 800; Min. Arm Extending Distance from Outriggers (mm): SDC0525-E: 600; SDC1025-E: 600; SDC1030-E: 600; Power Voltage (V): SDC0525-E: 380V; SDC1025-E: 380V; SDC1030-E: 380V; Weight (Kg): SDC0525-E: 1250; SDC1025-E: 1290; SDC1030-E: 1450; Overall size (mm) L*W*H: SDC0525-E: 3300*1200*1900; SDC1025-E: 3500*1300*1900; SDC1030-E: 3700*1500*1900; Turning Aisle (mm): SDC0525-E: 3500; SDC1025-E: 3700; SDC1030-E: 3900.
The specification sheet records Passing Aisle (mm): SDC0525-E: 1500; SDC1025-E: 1600; SDC1030-E: 1800; Pneumatic Tire (mm): SDC0525-E: 4*Ø400*80; SDC1025-E: 4*Ø500*80; SDC1030-E: 4*Ø500*80; Driving wheel (mm): 1*Ø250*80; Climbing slope (%): 4/6; Travel Speed (km/h): 4/6 Loaded/Unloaded; Lifting Speed (mm/s): 45/50 Loaded/Unloaded.
The specification sheet records Falling Speed (mm/s): 45/40 Loaded/Unloaded; Service Brake: Electromagnetic braking.
Units are copied as published; convert them only when comparing models.
Those missing values can be requested directly through the enquiry form.
Each row in the table keeps the label and value from the source record.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
The enquiry should list any attachment the job requires.
Match the power arrangement to the shifts and the working environment.
Review the tyre type against the surface the machine will run on.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
On the Electric floor crane SDC1030-E, list the attachments required, such as clamps, sideshift or rotator.
Check headroom under beams, pipes and door frames along the route.
On the Electric floor crane SDC1030-E, send photographs of the racking and the existing working area when possible.
Keep the charging or refuelling position clear of the main traffic aisle.
On the Electric floor crane SDC1030-E, mark the stations where loads are picked up and dropped off each shift.
On the Electric floor crane SDC1030-E, attachments are secured before the machine leaves the station.
The operator follows the rated capacity marked on the chassis.
On the Electric floor crane SDC1030-E, the working area is kept clear of loose packaging and obstacles.
Battery or fuel levels are checked at the start of each shift.
On the Electric floor crane SDC1030-E, spare parts for wear items follow the parts manual after delivery.
The layout drawing shows where each machine sits in the operation.
On the Electric floor crane SDC1030-E, a mixed enquiry can list this model together with other families.
Storage cages and racking organise the loads it moves between stations.
On the Electric floor crane SDC1030-E, site conditions such as gradient, dust and moisture belong in the enquiry.
The specification sheet is the binding reference for listed values.
On the Electric floor crane SDC1030-E, attachments are quoted separately once the base chassis is fixed.
Capacity above the rated lift height follows the mast curve.
On the Electric floor crane SDC1030-E, loading is recorded before the container is sealed.
The operation and parts material travel with the machine.
On the Electric floor crane SDC1030-E, quote the serial number and component name when ordering spares.
Quotations follow the model, listed specification and destination port.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
The serial number identifies the build when parts are ordered later.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.