Electric floor crane SDC1030-C Electric floor crane SDC1030-C. This item belongs to the broader SUNRISE material handling catalogue.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | SDC0530-C; SDC1025-C; SDC1030-C |
| Capacity | SDC0530-C: 500; SDC1025-C: 1000; SDC1030-C: 1000 |
| Lifting Height | SDC0530-C: 3000; SDC1025-C: 2500; SDC1030-C: 3000 |
| Battery | SDC0530-C: 24/165; SDC1025-C: 24/165; SDC1030-C: 24/210 |
| Charger | SDC0530-C: 24/20; SDC1025-C: 24/20; SDC1030-C: 24/30 |
| Lifting motor | SDC0530-C: 2.5; SDC1025-C: 2.5; SDC1030-C: 2.5 |
| Driving motor | SDC0530-C: AC1.2; SDC1025-C: AC1.2; SDC1030-C: AC1.2 |
| Min. Arm Extending Distance from Outriggers | SDC0530-C: 1200; SDC1025-C: 1100; SDC1030-C: 900 |
| Weight | SDC0530-C: 660; SDC1025-C: 690; SDC1030-C: 710 |
| Overall size (mm) L*W*H | SDC0530-C: 2930*850*1800; SDC1025-C: 2980*850*1600; SDC1030-C: 2980*850*1800 |
| Turning Aisle | SDC0530-C: 3200; SDC1025-C: 3200; SDC1030-C: 3200 |
| Passing Aisle | SDC0530-C: 1100; SDC1025-C: 1100; SDC1030-C: 1100 |
| Driving wheel | SDC0530-C: 1*Ø250*80; SDC1025-C: 1*Ø250*80; SDC1030-C: 1*Ø250*80 |
| Auxiliary Wheels | SDC0530-C: 2*Ø150*50; SDC1025-C: 2*Ø150*50; SDC1030-C: 2*Ø150*50 |
| Front Wheels | SDC0530-C: 2*Ø150*75; SDC1025-C: 2*Ø150*75; SDC1030-C: 2*Ø150*75 |
| Climbing slope | SDC0530-C: 4/6; SDC1025-C: 4/6; SDC1030-C: 4/6 |
| Travel Speed | SDC0530-C: 4/6 Loaded/Unloaded; SDC1025-C: 4/6 Loaded/Unloaded; SDC1030-C: 4/6 Loaded/Unloaded |
| Lifting Speed | SDC0530-C: 45/50 Loaded/Unloaded; SDC1025-C: 45/50 Loaded/Unloaded; SDC1030-C: 45/50 Loaded/Unloaded |
| Falling Speed | SDC0530-C: 45/40 Loaded/Unloaded; SDC1025-C: 45/40 Loaded/Unloaded; SDC1030-C: 45/40 Loaded/Unloaded |
| Service Brake | Electromagnetic braking |
Gallery
All detail images published for this model.






Electric floor crane SDC1030-C Electric floor crane SDC1030-C, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
General handling
Published figures for this build: rated capacity SDC0530-C: 500; SDC1025-C: 1000; SDC1030-C: 1000, turning radius SDC0530-C: 3200; SDC1025-C: 3200; SDC1030-C: 3200.
Selection starts from the load per move and the space around it.
Selection starts from the load per move and the space around it.
The machine is specified against the load, floor and working height.
The enquiry should describe the station the equipment works at.
Check closed mast or chassis height against the lowest door on the route. Confirm the charger voltage or fuel type for your destination country.
The specification sheet records Model: SDC0530-C; SDC1025-C; SDC1030-C; Capacity (kg): SDC0530-C: 500; SDC1025-C: 1000; SDC1030-C: 1000; Lifting Height (mm): SDC0530-C: 3000; SDC1025-C: 2500; SDC1030-C: 3000; Battery (V/Ah): SDC0530-C: 24/165; SDC1025-C: 24/165; SDC1030-C: 24/210; Charger (V/A): SDC0530-C: 24/20; SDC1025-C: 24/20; SDC1030-C: 24/30; Lifting motor (Kw): SDC0530-C: 2.5; SDC1025-C: 2.5; SDC1030-C: 2.5.
The specification sheet records Driving motor (Kw): SDC0530-C: AC1.2; SDC1025-C: AC1.2; SDC1030-C: AC1.2; Min. Arm Extending Distance from Outriggers (mm): SDC0530-C: 1200; SDC1025-C: 1100; SDC1030-C: 900; Weight (Kg): SDC0530-C: 660; SDC1025-C: 690; SDC1030-C: 710; Overall size (mm) L*W*H: SDC0530-C: 2930*850*1800; SDC1025-C: 2980*850*1600; SDC1030-C: 2980*850*1800; Turning Aisle (mm): SDC0530-C: 3200; SDC1025-C: 3200; SDC1030-C: 3200; Passing Aisle (mm): SDC0530-C: 1100; SDC1025-C: 1100; SDC1030-C: 1100.
The specification sheet records Driving wheel (mm): SDC0530-C: 1*Ø250*80; SDC1025-C: 1*Ø250*80; SDC1030-C: 1*Ø250*80; Auxiliary Wheels (mm): SDC0530-C: 2*Ø150*50; SDC1025-C: 2*Ø150*50; SDC1030-C: 2*Ø150*50; Front Wheels (mm): SDC0530-C: 2*Ø150*75; SDC1025-C: 2*Ø150*75; SDC1030-C: 2*Ø150*75; Climbing slope (%): SDC0530-C: 4/6; SDC1025-C: 4/6; SDC1030-C: 4/6; Travel Speed (km/h): SDC0530-C: 4/6 Loaded/Unloaded; SDC1025-C: 4/6 Loaded/Unloaded; SDC1030-C: 4/6 Loaded/Unloaded; Lifting Speed (mm/s): SDC0530-C: 45/50 Loaded/Unloaded; SDC1025-C: 45/50 Loaded/Unloaded; SDC1030-C: 45/50 Loaded/Unloaded.
The specification sheet records Falling Speed (mm/s): SDC0530-C: 45/40 Loaded/Unloaded; SDC1025-C: 45/40 Loaded/Unloaded; SDC1030-C: 45/40 Loaded/Unloaded; Service Brake: Electromagnetic braking.
Those missing values can be requested directly through the enquiry form.
An em dash marks a value the source record did not publish.
Each row in the table keeps the label and value from the source record.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
The enquiry should list any attachment the job requires.
Dimensions in the table come from the source record.
List the models that clear each constraint before asking for a quote.
Check the chassis width against the aisle and the container door.
Check the machine weight against floor loading where the site is raised.
Review the tyre type against the surface the machine will run on.
On the Electric floor crane SDC1030-C, check headroom under beams, pipes and door frames along the route.
Keep the charging or refuelling position clear of the main traffic aisle.
On the Electric floor crane SDC1030-C, note any slope, threshold or step along the working route.
Measure the pallet footprint and the heaviest single load before comparing models.
On the Electric floor crane SDC1030-C, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the Electric floor crane SDC1030-C, unusual noise or movement is reported before further use.
Battery or fuel levels are checked at the start of each shift.
On the Electric floor crane SDC1030-C, loads are kept low while travelling between stations.
The working area is kept clear of loose packaging and obstacles.
On the Electric floor crane SDC1030-C, attachments such as clamps or rotators are matched to the load shape.
The receiving side pairs it with a dock ramp or platform where needed.
On the Electric floor crane SDC1030-C, a mixed enquiry can list this model together with other families.
Related models in the same group are listed on the family page.
On the Electric floor crane SDC1030-C, capacity above the rated lift height follows the mast curve.
Tyre choice should match the floor rather than the price list.
On the Electric floor crane SDC1030-C, attachments are quoted separately once the base chassis is fixed.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the Electric floor crane SDC1030-C, the enquiry should include the quantity and destination port.
Quotations follow the model, listed specification and destination port.
On the Electric floor crane SDC1030-C, quote the serial number and component name when ordering spares.
The booking reference is issued with the proforma invoice.
The serial number identifies the build when parts are ordered later.
The operation material covers controls, checks and routine service points.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.