ZX14J-A1 Forklift attachment. The machine is specified against the load, floor and working height.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| ZX14J-A1 | 1400@710 / 560-1920 / 1200 / 1420 / 445 / 360 / 1040 / 825 / 750 / 113 |
| Model | Pressure value(Bar) / Flow value(L/min) |
| Maximum | Rotary Action / Clamping action |
| Least | Recommend / Maximum / Least |
| ZX**J | 160 / 4 / 15 / 38 / 19 / 26 |
Gallery
All detail images published for this model.



ZX14J-A1 Forklift attachment, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Attachment and auxiliary handling
The enquiry should describe the station the equipment works at.
Dimensions on the datasheet are checked against the site layout.
This item belongs to the broader SUNRISE material handling catalogue.
The enquiry should describe the station the equipment works at.
Confirm the charger voltage or fuel type for your destination country. Describe the shifts per day when the power arrangement is selected.
The specification sheet records ZX14J-A1: 1400@710 / 560-1920 / 1200 / 1420 / 445 / 360 / 1040 / 825 / 750 / 113; Model: Pressure value(Bar) / Flow value(L/min); Maximum: Rotary Action / Clamping action; Least: Recommend / Maximum / Least; ZX**J: 160 / 4 / 15 / 38 / 19 / 26.
Remaining parameters are listed row by row in the specification table.
An em dash marks a value the source record did not publish.
Rated figures apply at the standard load centre unless a row says otherwise.
Options and attachments are listed separately from the base chassis.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
The enquiry should list any attachment the job requires.
Dimensions in the table come from the source record.
List the models that clear each constraint before asking for a quote.
Check the machine weight against floor loading where the site is raised.
Compare the lowered height against the lowest door on the route.
Compare capacity first, then the lift height the job actually needs.
On the ZX14J-A1, state the shifts per day so the power arrangement can be sized properly.
Mark the stations where loads are picked up and dropped off each shift.
On the ZX14J-A1, measure the pallet footprint and the heaviest single load before comparing models.
Check the lowest door, beam height and aisle the truck has to pass through.
On the ZX14J-A1, send photographs of the racking and the existing working area when possible.
On the ZX14J-A1, battery or fuel levels are checked at the start of each shift.
Routine checks cover tyres, brakes, controls and visible leaks.
On the ZX14J-A1, unusual noise or movement is reported before further use.
Attachments are secured before the machine leaves the station.
On the ZX14J-A1, related models in the same group are listed on the family page.
The receiving side pairs it with a dock ramp or platform where needed.
On the ZX14J-A1, a mixed enquiry can list this model together with other families.
Storage cages and racking organise the loads it moves between stations.
On the ZX14J-A1, any option not listed should be confirmed in writing before order.
Tyre choice should match the floor rather than the price list.
On the ZX14J-A1, site conditions such as gradient, dust and moisture belong in the enquiry.
The specification sheet is the binding reference for listed values.
On the ZX14J-A1, wear parts are supplied after delivery against the parts manual.
The operation and parts material travel with the machine.
On the ZX14J-A1, quote the serial number and component name when ordering spares.
Loading is recorded before the container is sealed.
The parts manual lists the wear items and their reference views.
Ask for the specific certificate required for your target country.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.