GZS90 / 90A / 90B Hand Truck. Dimensions on the datasheet are checked against the site layout.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|
GZS90 / 90A / 90B Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Manual trolley duties
Dimensions on the datasheet are checked against the site layout.
The enquiry should describe the station the equipment works at.
This item belongs to the broader SUNRISE material handling catalogue.
The enquiry should describe the station the equipment works at.
Confirm the aisle width against the pallet depth before choosing a chassis. Describe the shifts per day when the power arrangement is selected.
The specification sheet records Length L is not published in the source record; Width W is not published in the source record; Handle Height H is not published in the source record.
Remaining parameters are listed row by row in the specification table.
An em dash marks a value the source record did not publish.
Options and attachments are listed separately from the base chassis.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Measure the pallet footprint before the chassis is shortlisted.
Door and beam heights decide which mast will clear the route.
Check the chassis width against the aisle and the container door.
List the models that clear each constraint before asking for a quote.
Compare the lowered height against the lowest door on the route.
Compare capacity first, then the lift height the job actually needs.
On the GZS90 / 90A / 90B, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
List the attachments required, such as clamps, sideshift or rotator.
On the GZS90 / 90A / 90B, mark the stations where loads are picked up and dropped off each shift.
Measure the pallet footprint and the heaviest single load before comparing models.
On the GZS90 / 90A / 90B, note any slope, threshold or step along the working route.
On the GZS90 / 90A / 90B, unusual noise or movement is reported before further use.
The operator follows the rated capacity marked on the chassis.
On the GZS90 / 90A / 90B, routine checks cover tyres, brakes, controls and visible leaks.
Loads are kept low while travelling between stations.
On the GZS90 / 90A / 90B, the layout drawing shows where each machine sits in the operation.
This machine usually works alongside pallet trucks and stacking equipment.
On the GZS90 / 90A / 90B, spare parts for wear items follow the parts manual after delivery.
The receiving side pairs it with a dock ramp or platform where needed.
On the GZS90 / 90A / 90B, site conditions such as gradient, dust and moisture belong in the enquiry.
Capacity above the rated lift height follows the mast curve.
On the GZS90 / 90A / 90B, the specification sheet is the binding reference for listed values.
Tyre choice should match the floor rather than the price list.
On the GZS90 / 90A / 90B, mixed equipment can be listed on one enquiry.
Quote the serial number and component name when ordering spares.
On the GZS90 / 90A / 90B, wear parts are supplied after delivery against the parts manual.
The operation and parts material travel with the machine.
Test and conformity documents follow the model and destination market.
The serial number identifies the build when parts are ordered later.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.