GZT150D-1 / 150A-1 / A-2 Hand Truck. This item belongs to the broader SUNRISE material handling catalogue.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.

GZT150D-1 / 150A-1 / A-2 Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Hand carrying and moving loads
Each build is quoted line by line once the duty cycle is confirmed.
Each build is quoted line by line once the duty cycle is confirmed.
The machine is specified against the load, floor and working height.
Selection starts from the load per move and the space around it.
State any attachment required alongside the base model. Match the tyre type to the floor surface rather than the price list.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Options and attachments are listed separately from the base chassis.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
The listed figures follow the record; options are confirmed on the quotation.
Review the tyre type against the surface the machine will run on.
Note any attachment that changes the load centre or the overall width.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
On the GZT150D-1 / 150A-1 / A-2, list the attachments required, such as clamps, sideshift or rotator.
Check headroom under beams, pipes and door frames along the route.
On the GZT150D-1 / 150A-1 / A-2, measure the pallet footprint and the heaviest single load before comparing models.
State the shifts per day so the power arrangement can be sized properly.
On the GZT150D-1 / 150A-1 / A-2, check the lowest door, beam height and aisle the truck has to pass through.
On the GZT150D-1 / 150A-1 / A-2, the working area is kept clear of loose packaging and obstacles.
Routine checks cover tyres, brakes, controls and visible leaks.
On the GZT150D-1 / 150A-1 / A-2, the operator follows the rated capacity marked on the chassis.
Attachments are secured before the machine leaves the station.
On the GZT150D-1 / 150A-1 / A-2, a mixed enquiry can list this model together with other families.
The receiving side pairs it with a dock ramp or platform where needed.
On the GZT150D-1 / 150A-1 / A-2, this machine usually works alongside pallet trucks and stacking equipment.
Spare parts for wear items follow the parts manual after delivery.
On the GZT150D-1 / 150A-1 / A-2, capacity above the rated lift height follows the mast curve.
The signed datasheet issued with the quotation is the binding version.
On the GZT150D-1 / 150A-1 / A-2, the specification sheet is the binding reference for listed values.
Tyre choice should match the floor rather than the price list.
On the GZT150D-1 / 150A-1 / A-2, quote the serial number and component name when ordering spares.
Packing follows sea-freight practice for the chosen chassis.
On the GZT150D-1 / 150A-1 / A-2, mixed equipment can be listed on one enquiry.
Wear parts are supplied after delivery against the parts manual.
The operation material covers controls, checks and routine service points.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.