AHT200 / GZT200 Hand Truck. Each build is quoted line by line once the duty cycle is confirmed.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.

AHT200 / GZT200 Hand Truck, part of the Special-purpose handling equipment line.
Hand trucks and trolleys, stair-climbing carts, paper-roll and coil clamps, forklift attachments, jacks and other auxiliary tools that do not fit the powered-vehicle families.
Pushed hand-truck transport
Each build is quoted line by line once the duty cycle is confirmed.
The enquiry should describe the station the equipment works at.
Each build is quoted line by line once the duty cycle is confirmed.
This item belongs to the broader SUNRISE material handling catalogue.
Confirm the aisle width against the pallet depth before choosing a chassis. Note cold store, outdoor gradient or container entry as a constraint.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Those missing values can be requested directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
The enquiry should list any attachment the job requires.
Compare the lowered height against the lowest door on the route.
Check the chassis width against the aisle and the container door.
Review the tyre type against the surface the machine will run on.
Check the machine weight against floor loading where the site is raised.
On the AHT200 / GZT200, keep the charging or refuelling position clear of the main traffic aisle.
Send photographs of the racking and the existing working area when possible.
On the AHT200 / GZT200, check the lowest door, beam height and aisle the truck has to pass through.
Check headroom under beams, pipes and door frames along the route.
On the AHT200 / GZT200, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the AHT200 / GZT200, attachments are secured before the machine leaves the station.
The operator checks load stability before each lift or move.
On the AHT200 / GZT200, the operator follows the rated capacity marked on the chassis.
Loads are kept low while travelling between stations.
On the AHT200 / GZT200, spare parts for wear items follow the parts manual after delivery.
The receiving side pairs it with a dock ramp or platform where needed.
On the AHT200 / GZT200, this machine usually works alongside pallet trucks and stacking equipment.
Attachments such as clamps or rotators are matched to the load shape.
On the AHT200 / GZT200, any option not listed should be confirmed in writing before order.
The specification sheet is the binding reference for listed values.
On the AHT200 / GZT200, capacity above the rated lift height follows the mast curve.
Attachments are quoted separately once the base chassis is fixed.
On the AHT200 / GZT200, the enquiry should include the quantity and destination port.
The booking reference is issued with the proforma invoice.
On the AHT200 / GZT200, loading is recorded before the container is sealed.
Packing follows sea-freight practice for the chosen chassis.
The operation material covers controls, checks and routine service points.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Special-purpose handling equipment related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.