Vertical Boom Platforms A6E A8E A10E Vertical Boom Platforms A6E A8E A10E. Maintenance, fit-out and warehousing at height are the usual jobs.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | Working height Capacity Max work outreach Dimensions Battery Weight |
| A6E | 5.50m 120kgs ----- 1.51x0.81x1.37 24V 180Ah 780 |
| A8E | 8.10m 200kgs 3.30m 2.8x0.99x1.99 24V 280Ah 2750kgs |
| A10E | 9.86m 200kgs 3.30m 2.8x0.99x1.99 24V 280Ah 2800 |
Gallery
All detail images published for this model.

Vertical Boom Platforms A6E A8E A10E Vertical Boom Platforms A6E A8E A10E, part of the Aerial work platforms line.
Scissor, boom and vertical-mast platforms for maintenance, fit-out and installation heights.
Inspection at height
Outdoor use depends on ground firmness and wind exposure on site.
Scissor and boom platforms suit positions a ladder cannot reach safely.
Guard rails and a platform replace climbing on racking or frames.
Outdoor use depends on ground firmness and wind exposure on site.
Confirm the aisle width against the pallet depth before choosing a chassis. Compare rated capacity against the heaviest single load you move.
The specification sheet records Model: Working height Capacity Max work outreach Dimensions Battery Weight; A6E: 5.50m 120kgs ----- 1.51x0.81x1.37 24V 180Ah 780; A8E: 8.10m 200kgs 3.30m 2.8x0.99x1.99 24V 280Ah 2750kgs; A10E: 9.86m 200kgs 3.30m 2.8x0.99x1.99 24V 280Ah 2800.
Remaining parameters are listed row by row in the specification table.
Rated figures apply at the standard load centre unless a row says otherwise.
Those missing values can be requested directly through the enquiry form.
Each row in the table keeps the label and value from the source record.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
The enquiry should list any attachment the job requires.
List the models that clear each constraint before asking for a quote.
Match the power arrangement to the shifts and the working environment.
Compare the lowered height against the lowest door on the route.
Check the machine weight against floor loading where the site is raised.
On the Vertical Boom Platforms A6E A8E A10E, check headroom under beams, pipes and door frames along the route.
Check the lowest door, beam height and aisle the truck has to pass through.
On the Vertical Boom Platforms A6E A8E A10E, mark the stations where loads are picked up and dropped off each shift.
List the attachments required, such as clamps, sideshift or rotator.
On the Vertical Boom Platforms A6E A8E A10E, measure the pallet footprint and the heaviest single load before comparing models.
On the Vertical Boom Platforms A6E A8E A10E, routine checks cover tyres, brakes, controls and visible leaks.
Unusual noise or movement is reported before further use.
On the Vertical Boom Platforms A6E A8E A10E, battery or fuel levels are checked at the start of each shift.
Loads are kept low while travelling between stations.
On the Vertical Boom Platforms A6E A8E A10E, the layout drawing shows where each machine sits in the operation.
The receiving side pairs it with a dock ramp or platform where needed.
On the Vertical Boom Platforms A6E A8E A10E, this machine usually works alongside pallet trucks and stacking equipment.
A mixed enquiry can list this model together with other families.
On the Vertical Boom Platforms A6E A8E A10E, site conditions such as gradient, dust and moisture belong in the enquiry.
Any option not listed should be confirmed in writing before order.
On the Vertical Boom Platforms A6E A8E A10E, the signed datasheet issued with the quotation is the binding version.
The specification sheet is the binding reference for listed values.
On the Vertical Boom Platforms A6E A8E A10E, quotations follow the model, listed specification and destination port.
Wear parts are supplied after delivery against the parts manual.
On the Vertical Boom Platforms A6E A8E A10E, quote the serial number and component name when ordering spares.
Documents issued for an order are listed in the quotation.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Aerial work platforms related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.