Manuel moving, electric vacuum lifter Vacuum lifter. Glass, stone, metal sheet and plasterboard are handled with pad frames.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Manuel moving, electric vacuum lifter Vacuum lifter, part of the Vacuum lifters line.
Vacuum suction lifters and frames for glass, stone, metal sheet and panel installation.
Suction pad sheet handling
Seal condition is checked before each lift on a smooth surface.
Pads are matched to the sheet surface and the load weight.
Rotation and tilting let one operator place a panel into a rack.
The lifter pairs with a crane, forklift attachment or its own battery frame.
Note cold store, outdoor gradient or container entry as a constraint. Compare rated capacity against the heaviest single load you move.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Those missing values can be requested directly through the enquiry form.
Units are copied as published; convert them only when comparing models.
Options and attachments are listed separately from the base chassis.
Configuration follows the load, working height and site layout.
Dimensions in the table come from the source record.
Measure the pallet footprint before the chassis is shortlisted.
Check the machine weight against floor loading where the site is raised.
Review the tyre type against the surface the machine will run on.
Compare the lowered height against the lowest door on the route.
Match the power arrangement to the shifts and the working environment.
On the Manuel moving, electric vacuum lifter, keep the charging or refuelling position clear of the main traffic aisle.
Check headroom under beams, pipes and door frames along the route.
On the Manuel moving, electric vacuum lifter, check the lowest door, beam height and aisle the truck has to pass through.
Note any slope, threshold or step along the working route.
On the Manuel moving, electric vacuum lifter, measure the pallet footprint and the heaviest single load before comparing models.
On the Manuel moving, electric vacuum lifter, the operator checks load stability before each lift or move.
Attachments are secured before the machine leaves the station.
On the Manuel moving, electric vacuum lifter, the working area is kept clear of loose packaging and obstacles.
Battery or fuel levels are checked at the start of each shift.
On the Manuel moving, electric vacuum lifter, a mixed enquiry can list this model together with other families.
Storage cages and racking organise the loads it moves between stations.
On the Manuel moving, electric vacuum lifter, the receiving side pairs it with a dock ramp or platform where needed.
Related models in the same group are listed on the family page.
On the Manuel moving, electric vacuum lifter, any option not listed should be confirmed in writing before order.
Dimensions are checked against the source record before quoting.
On the Manuel moving, electric vacuum lifter, the specification sheet is the binding reference for listed values.
The signed datasheet issued with the quotation is the binding version.
On the Manuel moving, electric vacuum lifter, loading is recorded before the container is sealed.
Quotations follow the model, listed specification and destination port.
On the Manuel moving, electric vacuum lifter, the enquiry should include the quantity and destination port.
The operation and parts material travel with the machine.
The serial number identifies the build when parts are ordered later.
Test and conformity documents follow the model and destination market.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Vacuum lifters related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.