GTBZ20 / GTBZ22Z Boom lift, rated capacity 480kg. Guard rails and a platform replace climbing on racking or frames.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | GTBZ20 / GTBZ22Z |
| Measurements | Metric system / British System |
| Lift capacity | 480 kg |
| Lift capacity | 340 kg / / 250 kg |
| Platform rotation | 160° |
| Jib rotation | 135° |
| Turntable Swing | 360°continuous |
| Turntable tailswing | 1.19m / 4ft |
| Travel speed -stowed | 6.3km/h / 3.9mph |
| Travel speed -raised or extended | 1.3km/h / 0.8mph |
| Gradeability -stowed | 30% |
| Gradeability -stowed | 45% |
| Turning radius - inside | 3.0m / 9ft7in |
| Turning radius - outside | 5.2m / 16ft8in |
| Controls | 24V DC Proportional |
| Solid tires | 9.00-20 |
| 2WD | 13000 kg / / 13140 kg |
| MODEL | GTBZ20 / GTBZ22Z |
| Measurements | Metric system / British System |
| Working height maximum | 22.4m / 73ft / 23.9m / 78ft |
| Platform height maximum | 20.7m / 68ft / 22.2m / 73ft |
| Horizontal reach maximum | 19.1m / 63ft / 20.2m / 66ft |
| Below ground reach | 1.76m / 5ft9in / 2.93m / 9ft7in |
| A | Platform width-8ft model / 0.91m / 3ft |
| Platform width-6ft model | 0.76m / 2ft |
| B | Platform length-8ft model / 2.44m / 8ft |
| Platform length -6ft model | 1.83m / 6ft |
| C | Height-stowed / 2.7m / 9ft |
| D | Length-stowed / 9.59m / 31ft / 10.69m / 35ft |
| E | Width / 2.49m / 8ft |
| F | Wheelbase / 2.5m / 8ft |
| G | Ground clearance-center / 0.43m / 1ft5in |
GTBZ20 / GTBZ22Z Boom lift, part of the Aerial work platforms line.
Scissor, boom and vertical-mast platforms for maintenance, fit-out and installation heights.
Platform-based height work
Published figures for this build: rated capacity 480 kg, turning radius 3.0m / 9ft7in.
Scissor and boom platforms suit positions a ladder cannot reach safely.
Outdoor use depends on ground firmness and wind exposure on site.
Scissor and boom platforms suit positions a ladder cannot reach safely.
Outdoor use depends on ground firmness and wind exposure on site.
Confirm the aisle width against the pallet depth before choosing a chassis. Check closed mast or chassis height against the lowest door on the route.
The specification sheet records Model: GTBZ20 / GTBZ22Z; Measurements: Metric system / British System; Lift capacity (restricted): 480 kg; Lift capacity (non-restricted): 340 kg / / 250 kg; Platform rotation: 160°; Jib rotation: 135°.
The specification sheet records Turntable Swing: 360°continuous; Turntable tailswing: 1.19m / 4ft; Travel speed -stowed: 6.3km/h / 3.9mph; Travel speed -raised or extended: 1.3km/h / 0.8mph; Gradeability -stowed (2WD): 30%; Gradeability -stowed (4WD): 45%.
The specification sheet records Turning radius - inside: 3.0m / 9ft7in; Turning radius - outside: 5.2m / 16ft8in; Controls: 24V DC Proportional; Solid tires: 9.00-20; WEIGHT is not published in the source record; 2WD (kg): 13000 kg / / 13140 kg.
The specification sheet records MODEL: GTBZ20 / GTBZ22Z; Measurements: Metric system / British System; Working height maximum: 22.4m / 73ft / 23.9m / 78ft; Platform height maximum: 20.7m / 68ft / 22.2m / 73ft; Horizontal reach maximum: 19.1m / 63ft / 20.2m / 66ft; Below ground reach: 1.76m / 5ft9in / 2.93m / 9ft7in.
The specification sheet records A: Platform width-8ft model / 0.91m / 3ft; Platform width-6ft model: 0.76m / 2ft; B: Platform length-8ft model / 2.44m / 8ft; Platform length -6ft model: 1.83m / 6ft; C: Height-stowed / 2.7m / 9ft; D: Length-stowed / 9.59m / 31ft / 10.69m / 35ft.
The specification sheet records E: Width / 2.49m / 8ft; F: Wheelbase / 2.5m / 8ft; G: Ground clearance-center / 0.43m / 1ft5in.
Units are copied as published; convert them only when comparing models.
Rated figures apply at the standard load centre unless a row says otherwise.
Options and attachments are listed separately from the base chassis.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
The enquiry should list any attachment the job requires.
The listed figures follow the record; options are confirmed on the quotation.
List the models that clear each constraint before asking for a quote.
Note any attachment that changes the load centre or the overall width.
Check the chassis width against the aisle and the container door.
Compare capacity first, then the lift height the job actually needs.
On the GTBZ20 / GTBZ22Z, keep the charging or refuelling position clear of the main traffic aisle.
Check headroom under beams, pipes and door frames along the route.
On the GTBZ20 / GTBZ22Z, note any slope, threshold or step along the working route.
Measure the pallet footprint and the heaviest single load before comparing models.
On the GTBZ20 / GTBZ22Z, mark the stations where loads are picked up and dropped off each shift.
On the GTBZ20 / GTBZ22Z, the working area is kept clear of loose packaging and obstacles.
Loads are kept low while travelling between stations.
On the GTBZ20 / GTBZ22Z, attachments are secured before the machine leaves the station.
Unusual noise or movement is reported before further use.
On the GTBZ20 / GTBZ22Z, the receiving side pairs it with a dock ramp or platform where needed.
The layout drawing shows where each machine sits in the operation.
On the GTBZ20 / GTBZ22Z, spare parts for wear items follow the parts manual after delivery.
Attachments such as clamps or rotators are matched to the load shape.
On the GTBZ20 / GTBZ22Z, the signed datasheet issued with the quotation is the binding version.
The specification sheet is the binding reference for listed values.
On the GTBZ20 / GTBZ22Z, attachments are quoted separately once the base chassis is fixed.
Capacity above the rated lift height follows the mast curve.
On the GTBZ20 / GTBZ22Z, mixed equipment can be listed on one enquiry.
The operation and parts material travel with the machine.
On the GTBZ20 / GTBZ22Z, packing follows sea-freight practice for the chosen chassis.
Quote the serial number and component name when ordering spares.
The parts manual lists the wear items and their reference views.
Ask for the specific certificate required for your target country.
Test and conformity documents follow the model and destination market.
Questions
The listed rated capacity is 480kg at the standard load centre. Above the rated lift height capacity derates along the mast curve.
The listed tyre type is 9.00-20. Solid tyres suit sealed concrete; pneumatic tyres suit rough outdoor ground.
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Aerial work platforms related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.