Guangzhou, China ISO 9001 · ISO 14001 · ISO 18001 CE / GS tested by TÜV Rheinland
Sales desk Guangzhou · +86 198 6588 7686
All equipment families257 modelsBuying guides13ForkliftDiesel forklift trucks9Electric forklift trucks11LPG and gas forklift trucks7StackerReach stackers10Stackers and order pickers33Pallet truckPallet trucks25Lift table and drum handlingDrum handlers11Lift tables20Vacuum lifterVacuum lifters19Aerial work platformAerial work platforms14Electric tractorElectric tow tractors9ConveyorConveyors9Loading rampDock ramps7Storage systemStorage systems28Other handling equipmentSpecial-purpose handling equipment45 Videos Buying guides Search models Certificates Buyer FAQ About us Contact us Request a quote

ESL50 — stacker

ESL50 Self lift stacker, rated capacity 500 kg. Stackers work in narrow aisles where a counterbalance truck will not turn.

ESL50 stacker — product photo 1 of 5
Key published figures Full specification →

Ordering facts for the ESL50

Confirmed terms
Minimum order
1 set — mixed models can be combined in one container.
Lead time
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days.
Payment
T/T 30% deposit, 70% balance against copy of the bill of lading.
Loading ports
Guangzhou, Shenzhen or Nansha.
Certification
CE on the product range; the factory holds ISO 9001, ISO 14001 and ISO 18001.
Warranty
12 months from delivery.
Price
Prices are not published on this site — every offer is quoted line by line against the load, lift height, floor condition and destination port.

Specification

ESL50 specification

Values are copied from the source record in their original order and units.

ESL50 specification table
ParameterUnitESL50/09ESL50/10ESL50/11ESL50/13
Model—ESL50/09ESL50/10ESL50/11ESL50/13
Capacitykg500500500500
Lifting heightmm900100011001300
Load centermm400400400400
Type of lifting—Electric
Wheel basemm860860860860
Front wheel basemm380380380380
Back wheel basemm670670670670
Bearing wheel sizemmΦ70×60Φ70×60Φ70×60Φ70×60
Steering wheel sizemmΦ100×50Φ100×50Φ100×50Φ100×50
Balance wheel sizemmΦ40×26Φ40×26Φ40×26Φ40×26
Training wheel sizemmΦ30×26Φ30×26Φ30×26Φ30×26
Min.fork heightmm90909090
Fork outside widthmm535535535535
Fork inside widthmm225225225225
Fork lengthmm1150115011501150
Single fork size—e/s(mm) 155/60 155/60 155/60 155/60
Overall lengthmm1565156516001600
Overall widthmm790790790790
Overall heightmm1195125014001600
Whole heightafter tape file shelf2100230025002900
Min.turning radiusmm1120112011201120
Lifting speedladen/unladenmm/s 80/110 80/110 80/110 80/110
Lowering speedladen/unladenmm/s 80/80 80/80 80/80 80/80
Lift motorkw12/0.8 12/0.8 12V0.8 12V0.8
Battery capacityv/ah12/33 12/33 12/33 12/33
Battery weightkg10101010
Net weightkg175186197219
Request price Datasheet (print / save as PDF) Ask about voltage

Gallery

Product photographs

All detail images published for this model.

What this model is built to do

ESL50 Self lift stacker, part of the Stackers and order pickers line.

Walk-behind, ride-on and semi-electric stackers plus order picking platform trucks.

Walk-behind pallet lifting

Published figures for this build: rated capacity 500 500 500 500 kg, overall width 790 790 790 790 mm, turning radius 1120 1120 1120 1120 mm.

The walk-behind model leaves the operator free to guide each load.

Stackers work in narrow aisles where a counterbalance truck will not turn.

Walk-behind and stand-on stackers put loads straight onto racking.

Straddle legs carry the mast forward for a much narrower aisle.

Match the tyre type to the floor surface rather than the price list. Compare rated capacity against the heaviest single load you move.

Specification walk-through

The specification sheet records Model: ESL50/09 / ESL50/10 / ESL50/11 / ESL50/13; Capacity (kg): 500 / 500 / 500 / 500; Lifting height (mm): 900 / 1000 / 1100 / 1300; Load center (mm): 400 / 400 / 400 / 400; Type of lifting: Electric; Wheel base (mm): 860 / 860 / 860 / 860.

The specification sheet records Front wheel base (mm): 380 / 380 / 380 / 380; Back wheel base (mm): 670 / 670 / 670 / 670; Bearing wheel size (mm): Φ70×60 / Φ70×60 / Φ70×60 / Φ70×60; Steering wheel size (mm): Φ100×50 / Φ100×50 / Φ100×50 / Φ100×50; Balance wheel size (mm): Φ40×26 / Φ40×26 / Φ40×26 / Φ40×26; Training wheel size (mm): Φ30×26 / Φ30×26 / Φ30×26 / Φ30×26.

The specification sheet records Min.fork height (mm): 90 / 90 / 90 / 90; Fork outside width (mm): 535 / 535 / 535 / 535; Fork inside width (mm): 225 / 225 / 225 / 225; Fork length (mm): 1150 / 1150 / 1150 / 1150; Single fork size: e/s(mm) 155/60 155/60 155/60 155/60; Overall length (mm): 1565 / 1565 / 1600 / 1600.

The specification sheet records Overall width (mm): 790 / 790 / 790 / 790; Overall height (mm): 1195 / 1250 / 1400 / 1600; Whole height (after tape file shelf): 2100 / 2300 / 2500 / 2900; Min.turning radius (mm): 1120 / 1120 / 1120 / 1120; Lifting speed (laden/unladen): mm/s 80/110 80/110 80/110 80/110; Lowering speed (laden/unladen): mm/s 80/80 80/80 80/80 80/80.

The specification sheet records Lift motor (kw): 12/0.8 12/0.8 12V0.8 12V0.8; Battery capacity (v/ah): 12/33 12/33 12/33 12/33; Battery weight (kg): 10 / 10 / 10 / 10; Net weight (kg): 175 / 186 / 197 / 219.

Rated figures apply at the standard load centre unless a row says otherwise.

Options and attachments are listed separately from the base chassis.

Units are copied as published; convert them only when comparing models.

Each row in the table keeps the label and value from the source record.

How to specify the right build

Configuration follows the load, working height and site layout.

The enquiry should list any attachment the job requires.

The listed figures follow the record; options are confirmed on the quotation.

Review the tyre type against the surface the machine will run on.

Check the machine weight against floor loading where the site is raised.

Compare the lowered height against the lowest door on the route.

Note any attachment that changes the load centre or the overall width.

  • List the load per move, lift height and floor surface before comparing models.
  • Mark the stations where loads are picked up and dropped off each shift.
  • Send those figures with the model code; the reply confirms whether the chassis suits.

Site preparation and operating notes

On the ESL50, measure the pallet footprint and the heaviest single load before comparing models.

Send photographs of the racking and the existing working area when possible.

On the ESL50, state the shifts per day so the power arrangement can be sized properly.

Check headroom under beams, pipes and door frames along the route.

On the ESL50, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.

Operation and routine checks

On the ESL50, the operator follows the rated capacity marked on the chassis.

Routine checks cover tyres, brakes, controls and visible leaks.

On the ESL50, battery or fuel levels are checked at the start of each shift.

The operator checks load stability before each lift or move.

How this model fits the operation

On the ESL50, storage cages and racking organise the loads it moves between stations.

A mixed enquiry can list this model together with other families.

On the ESL50, this machine usually works alongside pallet trucks and stacking equipment.

Related models in the same group are listed on the family page.

Working conditions and honest limits

On the ESL50, attachments are quoted separately once the base chassis is fixed.

Any option not listed should be confirmed in writing before order.

On the ESL50, tyre choice should match the floor rather than the price list.

Site conditions such as gradient, dust and moisture belong in the enquiry.

Delivery, documents and support

On the ESL50, the enquiry should include the quantity and destination port.

Quotations follow the model, listed specification and destination port.

On the ESL50, wear parts are supplied after delivery against the parts manual.

The booking reference is issued with the proforma invoice.

Ask for the specific certificate required for your target country.

Test and conformity documents follow the model and destination market.

The operation material covers controls, checks and routine service points.

Before you order

  • The rated load applies at the standard load centre; carrying the load farther forward reduces the figure marked on the chassis plate.
  • Measure the lowered chassis and mast height against the lowest door and the container door on the planned route.
  • Any clamp, sideshift or rotator changes the load centre and must be listed alongside the base model.
  • Documents issued with the order: ISO 9001, ISO 14001 and ISO 18001 factory certificates, plus CE or GS where the model carries it, and the serial list for the shipment.
  • Wear parts are ordered after delivery against the parts manual, the serial number and the component name.

Questions

Questions buyers ask before ordering

What load does the ESL50 carry?+

The listed rated capacity is 500 kg at the standard load centre. Above the rated lift height capacity derates along the mast curve.

What load centre applies to the rating?+

The specification lists a load centre of 400. Loads carried farther forward reduce rated capacity.

What aisle width does it need?+

The listed turning radius is 1120. Aisle width also depends on pallet depth and fork length.

What is the machine weight?+

The listed service or net weight is 10 kg. This matters for floor loading, ramps and container plans.

Can it enter a container or trailer?+

Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.

Which certifications accompany the machine?+

The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.

What is the lead time?+

Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.

How are spare parts handled after delivery?+

The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.

What information do you need for a quotation?+

Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.

Related

Other models in this family

Same-family comparison using the published source figures; open a model page for the full specification.

Stackers and order pickers related models

ModelCapacityLiftPowerTypical use
PWSR500 kg——Narrow-aisle put-away
WSR1000 kg——Walk-behind pallet lifting
CTY-A—1600—Low-level pallet stacking
CTY-D—1600—Narrow-aisle put-away
CTY-E—1600—Walk-behind pallet lifting

Explore

Related equipment and buying guides

Send the load and the working conditions

Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.

Tel0086-20-23357922
WhatsApp / WeChat0086-19865887686
OfficeRoom 2102, No.348 Tancun Road, Tianhe District, Guangzhou, China
We reply within 12 working hours.