Guangzhou, China ISO 9001 · ISO 14001 · ISO 18001 CE / GS tested by TÜV Rheinland
Sales desk Guangzhou · +86 198 6588 7686
All equipment families257 modelsBuying guides13ForkliftDiesel forklift trucks9Electric forklift trucks11LPG and gas forklift trucks7StackerReach stackers10Stackers and order pickers33Pallet truckPallet trucks25Lift table and drum handlingDrum handlers11Lift tables20Vacuum lifterVacuum lifters19Aerial work platformAerial work platforms14Electric tractorElectric tow tractors9ConveyorConveyors9Loading rampDock ramps7Storage systemStorage systems28Other handling equipmentSpecial-purpose handling equipment45 Videos Buying guides Search models Certificates Buyer FAQ About us Contact us Request a quote

NARROW AISLE FORKLIFT — electric counterbalance forklift

NARROW AISLE FORKLIFT NARROW AISLE FORKLIFT. The battery sits under the operator and acts as counterweight.

NARROW AISLE FORKLIFT electric counterbalance forklift — product photo 1 of 11

Ordering facts for the NARROW AISLE FORKLIFT

Confirmed terms
Minimum order
1 set — mixed models can be combined in one container.
Lead time
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days.
Payment
T/T 30% deposit, 70% balance against copy of the bill of lading.
Loading ports
Guangzhou, Shenzhen or Nansha.
Certification
CE on the product range; the factory holds ISO 9001, ISO 14001 and ISO 18001.
Warranty
12 months from delivery.
Price
Prices are not published on this site — every offer is quoted line by line against the load, lift height, floor condition and destination port.

Specification

NARROW AISLE FORKLIFT specification

Values are copied from the source record in their original order and units.

NARROW AISLE FORKLIFT specification table
ParameterValue
MODELNA30; NA25; NA20; NA15
CapacityNA30: 3000; NA25: 2500; NA20: 2000; NA15: 1500
Light heightNA30: 4300-12100; NA25: 4300-12100; NA20: 4300-10050; NA15: 4300-7050
Free liftNA30: 1365-4586; NA25: 1365-4586; NA20: 1365-3635; NA15: 1365-3335
Mast closed heightNA30: 2265-5460; NA25: 2265-5460; NA20: 2265-4615; NA15: 2265-2865
Extended heightNA30: 5561-12963; NA25: 5561-12963; NA20: 5561-11391; NA15: 5561-8311
Overall length2780
Ground clearance50
Overhead guard height2270
Chassis width rearNA30: 1600; NA25: 1400; NA20: 1220; NA15: 1030
Chassis width front980
Load center600
Wheel base1735
Seat height1220
Mast tilt (back/fwd)3/1
Rotate angle (left/right)220
Ground speed16
Lift speed (load/unload)0.44/0.5
Front tyre size412*174
Rear tyre sizeNA30/NA25: 457*170; NA20/NA15: 457*150
Grade ability (load/unload)18/20
Battery voltage/capacityNA30: 80v/500; NA25: 80v/500; NA20: 80v/500; NA15: 80v/400
Weight including batteryNA30: 7800; NA25: 7400; NA20: 6900; NA15: 6400
Weight excluding batteryNA30: 5810; NA25: 5510; NA20: 5310; NA15: 5150
Traction motor19.5 AC
Lifting motor15 AC
90° entrance widthNA30/NA25: 2150; NA20/NA15: 1960
Transfer aisle2700
Request price Datasheet (print / save as PDF) Ask about voltage

Gallery

Product photographs

All detail images published for this model.

What this model is built to do

NARROW AISLE FORKLIFT NARROW AISLE FORKLIFT, part of the Electric forklift trucks line.

Battery counterbalance and multi-directional forklifts for indoor warehouses and sealed-floor duty.

Racking aisle put-away

Published figures for this build: rated capacity NA30: 3000; NA25: 2500; NA20: 2000; NA15: 1500, turning radius 2700 mm, tyre 412*174 mm.

The compact chassis fits narrow indoor aisles and dock approaches.

Electric counterbalance trucks suit sealed floors and racking aisles.

Battery trucks keep noise and fumes low in covered storage areas.

Indoor shifts without exhaust are the main reason buyers choose electric.

Confirm the charger voltage or fuel type for your destination country. Note cold store, outdoor gradient or container entry as a constraint.

Specification walk-through

The specification sheet records MODEL: NA30; NA25; NA20; NA15; Capacity (kg): NA30: 3000; NA25: 2500; NA20: 2000; NA15: 1500; Light height (mm): NA30: 4300-12100; NA25: 4300-12100; NA20: 4300-10050; NA15: 4300-7050; Free lift (mm): NA30: 1365-4586; NA25: 1365-4586; NA20: 1365-3635; NA15: 1365-3335; Mast closed height (mm): NA30: 2265-5460; NA25: 2265-5460; NA20: 2265-4615; NA15: 2265-2865; Extended height (mm): NA30: 5561-12963; NA25: 5561-12963; NA20: 5561-11391; NA15: 5561-8311.

The specification sheet records Overall length (mm): 2780; Ground clearance (mm): 50; Overhead guard height (mm): 2270; Chassis width rear (mm): NA30: 1600; NA25: 1400; NA20: 1220; NA15: 1030; Chassis width front (mm): 980; Load center (mm): 600.

The specification sheet records Wheel base (mm): 1735; Seat height (mm): 1220; Mast tilt (back/fwd) (°): 3/1; Rotate angle (left/right) (°): 220; Ground speed (km/h): 16; Lift speed (load/unload) (m/s): 0.44/0.5.

The specification sheet records Front tyre size (mm): 412*174; Rear tyre size (mm): NA30/NA25: 457*170; NA20/NA15: 457*150; Grade ability (load/unload) (%): 18/20; Battery voltage/capacity (v/ah): NA30: 80v/500; NA25: 80v/500; NA20: 80v/500; NA15: 80v/400; Weight including battery (kg): NA30: 7800; NA25: 7400; NA20: 6900; NA15: 6400; Weight excluding battery (kg): NA30: 5810; NA25: 5510; NA20: 5310; NA15: 5150.

The specification sheet records Traction motor (kw): 19.5 AC; Lifting motor (kw): 15 AC; 90° entrance width (mm): NA30/NA25: 2150; NA20/NA15: 1960; Transfer aisle (mm): 2700.

Options and attachments are listed separately from the base chassis.

Each row in the table keeps the label and value from the source record.

An em dash marks a value the source record did not publish.

Those missing values can be requested directly through the enquiry form.

How to specify the right build

Configuration follows the load, working height and site layout.

The enquiry should list any attachment the job requires.

Door and beam heights decide which mast will clear the route.

List the models that clear each constraint before asking for a quote.

Check the machine weight against floor loading where the site is raised.

Check the chassis width against the aisle and the container door.

Note any attachment that changes the load centre or the overall width.

  • List attachments such as clamps, sideshift or rotator separately.
  • Note any constraint: low door, narrow aisle, cold store, outdoor gradient or entry.
  • Send those figures with the model code; the reply confirms whether the chassis suits.

Site preparation and operating notes

On the NARROW AISLE FORKLIFT, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.

State the shifts per day so the power arrangement can be sized properly.

On the NARROW AISLE FORKLIFT, mark the stations where loads are picked up and dropped off each shift.

Check the lowest door, beam height and aisle the truck has to pass through.

On the NARROW AISLE FORKLIFT, list the attachments required, such as clamps, sideshift or rotator.

Operation and routine checks

On the NARROW AISLE FORKLIFT, attachments are secured before the machine leaves the station.

Unusual noise or movement is reported before further use.

On the NARROW AISLE FORKLIFT, loads are kept low while travelling between stations.

Battery or fuel levels are checked at the start of each shift.

How this model fits the operation

On the NARROW AISLE FORKLIFT, storage cages and racking organise the loads it moves between stations.

Spare parts for wear items follow the parts manual after delivery.

On the NARROW AISLE FORKLIFT, related models in the same group are listed on the family page.

The layout drawing shows where each machine sits in the operation.

Working conditions and honest limits

On the NARROW AISLE FORKLIFT, any option not listed should be confirmed in writing before order.

The specification sheet is the binding reference for listed values.

On the NARROW AISLE FORKLIFT, site conditions such as gradient, dust and moisture belong in the enquiry.

The signed datasheet issued with the quotation is the binding version.

Delivery, documents and support

On the NARROW AISLE FORKLIFT, documents issued for an order are listed in the quotation.

The enquiry should include the quantity and destination port.

On the NARROW AISLE FORKLIFT, packing follows sea-freight practice for the chosen chassis.

Quotations follow the model, listed specification and destination port.

Ask for the specific certificate required for your target country.

The parts manual lists the wear items and their reference views.

The serial number identifies the build when parts are ordered later.

Before you order

  • Compare the published capacity against the heaviest single move before the mast or attachment is chosen.
  • Dimensions in the specification come from the source record — check them against the container door, the lowest door on the route and the aisle before ordering.
  • Any clamp, sideshift or rotator changes the load centre and must be listed alongside the base model.
  • The certificate set for an order follows the destination market; ISO factory certificates and the serial list ship with the consignment.
  • Wear parts are ordered after delivery against the parts manual, the serial number and the component name.

Questions

Questions buyers ask before ordering

Which tyres are fitted?+

The listed tyre type is 412*174. Solid tyres suit sealed concrete; pneumatic tyres suit rough outdoor ground.

What load centre applies to the rating?+

The specification lists a load centre of 600. Loads carried farther forward reduce rated capacity.

Can it enter a container or trailer?+

Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.

Which certifications accompany the machine?+

The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.

What is the lead time?+

Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.

How are spare parts handled after delivery?+

The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.

What information do you need for a quotation?+

Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.

What does the price depend on?+

Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.

What is the minimum order quantity?+

The minimum order quantity is one set, and mixed models can be combined in one container.

Related

Other models in this family

Same-family comparison using the published source figures; open a model page for the full specification.

Electric forklift trucks related models

ModelCapacityLiftPowerTypical use
CPDB10C———Indoor order picking
MK15-30—3000 mmElectricCovered storage shifts
Electric———Indoor order picking
Electric———Cold store and food plants
Electric———Cold store and food plants

Explore

Related equipment and buying guides

Send the load and the working conditions

Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.

Tel0086-20-23357922
WhatsApp / WeChat0086-19865887686
OfficeRoom 2102, No.348 Tancun Road, Tianhe District, Guangzhou, China
We reply within 12 working hours.