CDD15J Electric Stacker. The walk-behind model leaves the operator free to guide each load.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
CDD15J Electric Stacker, part of the Stackers and order pickers line.
Walk-behind, ride-on and semi-electric stackers plus order picking platform trucks.
Order picking at height
Stackers keep the pallet close to the legs while lifting at height.
Stackers keep the pallet close to the legs while lifting at height.
Walk-behind and stand-on stackers put loads straight onto racking.
Stackers keep the pallet close to the legs while lifting at height.
Match the tyre type to the floor surface rather than the price list. Describe the shifts per day when the power arrangement is selected.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Rated figures apply at the standard load centre unless a row says otherwise.
An em dash marks a value the source record did not publish.
Those missing values can be requested directly through the enquiry form.
Configuration follows the load, working height and site layout.
The listed figures follow the record; options are confirmed on the quotation.
Door and beam heights decide which mast will clear the route.
Note any attachment that changes the load centre or the overall width.
Check the machine weight against floor loading where the site is raised.
Compare the lowered height against the lowest door on the route.
Review the tyre type against the surface the machine will run on.
On the CDD15J, describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
State the shifts per day so the power arrangement can be sized properly.
On the CDD15J, check headroom under beams, pipes and door frames along the route.
Check the lowest door, beam height and aisle the truck has to pass through.
On the CDD15J, mark the stations where loads are picked up and dropped off each shift.
On the CDD15J, battery or fuel levels are checked at the start of each shift.
The operator follows the rated capacity marked on the chassis.
On the CDD15J, unusual noise or movement is reported before further use.
Routine checks cover tyres, brakes, controls and visible leaks.
On the CDD15J, attachments such as clamps or rotators are matched to the load shape.
Spare parts for wear items follow the parts manual after delivery.
On the CDD15J, related models in the same group are listed on the family page.
The receiving side pairs it with a dock ramp or platform where needed.
On the CDD15J, any option not listed should be confirmed in writing before order.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the CDD15J, the signed datasheet issued with the quotation is the binding version.
Attachments are quoted separately once the base chassis is fixed.
On the CDD15J, quotations follow the model, listed specification and destination port.
Mixed equipment can be listed on one enquiry.
On the CDD15J, the enquiry should include the quantity and destination port.
Quote the serial number and component name when ordering spares.
Test and conformity documents follow the model and destination market.
The parts manual lists the wear items and their reference views.
The operation material covers controls, checks and routine service points.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.