Electric counter-balance side loading roll lifter Electric counter-balance side loading roll lifter. The compact chassis fits narrow indoor aisles and dock approaches.

Specification
The source record did not publish a parameter table for this model. The listed figures below are limited to what the record confirms; request the missing parameters through the enquiry form.
Gallery
All detail images published for this model.





Electric counter-balance side loading roll lifter Electric counter-balance side loading roll lifter, part of the Electric forklift trucks line.
Battery counterbalance and multi-directional forklifts for indoor warehouses and sealed-floor duty.
Covered storage shifts
Warehouses, cold stores and food plants are common indoor duties.
Indoor shifts without exhaust are the main reason buyers choose electric.
Battery trucks keep noise and fumes low in covered storage areas.
Warehouses, cold stores and food plants are common indoor duties.
Confirm the aisle width against the pallet depth before choosing a chassis. Confirm the charger voltage or fuel type for your destination country.
The published parameters for this build are listed in the specification table.
Items the source record did not publish are shown as an em dash in the table.
Those missing items can be asked for directly through the enquiry form.
Options and attachments are listed separately from the base chassis.
Units are copied as published; convert them only when comparing models.
An em dash marks a value the source record did not publish.
Configuration follows the load, working height and site layout.
Door and beam heights decide which mast will clear the route.
Send pallet size, door height and aisle width with the enquiry.
Review the tyre type against the surface the machine will run on.
Match the power arrangement to the shifts and the working environment.
Note any attachment that changes the load centre or the overall width.
Check the chassis width against the aisle and the container door.
On the Electric counter-balance side loading roll lifter, check headroom under beams, pipes and door frames along the route.
Describe the floor surface: sealed concrete, asphalt, gravel or packed earth.
On the Electric counter-balance side loading roll lifter, mark the stations where loads are picked up and dropped off each shift.
Check the lowest door, beam height and aisle the truck has to pass through.
On the Electric counter-balance side loading roll lifter, keep the charging or refuelling position clear of the main traffic aisle.
On the Electric counter-balance side loading roll lifter, the operator checks load stability before each lift or move.
The operator follows the rated capacity marked on the chassis.
On the Electric counter-balance side loading roll lifter, the working area is kept clear of loose packaging and obstacles.
Battery or fuel levels are checked at the start of each shift.
On the Electric counter-balance side loading roll lifter, the layout drawing shows where each machine sits in the operation.
Spare parts for wear items follow the parts manual after delivery.
On the Electric counter-balance side loading roll lifter, attachments such as clamps or rotators are matched to the load shape.
This machine usually works alongside pallet trucks and stacking equipment.
On the Electric counter-balance side loading roll lifter, the signed datasheet issued with the quotation is the binding version.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the Electric counter-balance side loading roll lifter, the specification sheet is the binding reference for listed values.
Any option not listed should be confirmed in writing before order.
On the Electric counter-balance side loading roll lifter, loading is recorded before the container is sealed.
Documents issued for an order are listed in the quotation.
On the Electric counter-balance side loading roll lifter, packing follows sea-freight practice for the chosen chassis.
Wear parts are supplied after delivery against the parts manual.
Ask for the specific certificate required for your target country.
The parts manual lists the wear items and their reference views.
Test and conformity documents follow the model and destination market.
Questions
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Standard terms are T/T 30% deposit with 70% balance against copy of the bill of lading.
Shipment can be arranged from Guangzhou, Shenzhen or Nansha, whichever suits the sailing and the inland routing.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.