TFY100D Air/Hyd.table truck, rated capacity 1000Kg. The gas option works where diesel fumes are not acceptable indoors.

Specification
Values are copied from the source record in their original order and units.
| Parameter | Value |
|---|---|
| Model | TFY100D |
| Load Capacity | 1000 kg |
| Lowest Height | 380 mm |
| Max. Height | 1000 mm |
| Table Dimensions | 1200×610×55 mm |
| Total Length | 1600 mm |
| Length of Handle | 1000 mm |
| Net Weight | 170 kg |
TFY100D Air/Hyd.table truck, part of the LPG and gas forklift trucks line.
LPG and gasoline counterbalance trucks for mixed indoor-outdoor operation.
Mixed-fleet dock work
Published figures for this build: rated capacity 1000 kg.
The gas option works where diesel fumes are not acceptable indoors.
Gas power suits sites that alternate between yard and covered unloading.
Gas power suits sites that alternate between yard and covered unloading.
Mixed indoor-outdoor duty cycles are the usual reason to look at gas.
State any attachment required alongside the base model. Confirm the charger voltage or fuel type for your destination country.
The specification sheet records Model: TFY100D; Load Capacity (kg): 1000 kg; Lowest Height (mm): 380 mm; Max. Height (mm): 1000 mm; Table Dimensions (mm): 1200×610×55 mm; Total Length (mm): 1600 mm.
The specification sheet records Length of Handle (mm): 1000 mm; Net Weight (kg): 170 kg.
Rated figures apply at the standard load centre unless a row says otherwise.
Units are copied as published; convert them only when comparing models.
Those missing values can be requested directly through the enquiry form.
Each row in the table keeps the label and value from the source record.
Configuration follows the load, working height and site layout.
Send pallet size, door height and aisle width with the enquiry.
Door and beam heights decide which mast will clear the route.
Match the power arrangement to the shifts and the working environment.
Review the tyre type against the surface the machine will run on.
List the models that clear each constraint before asking for a quote.
Compare the lowered height against the lowest door on the route.
On the TFY100D, state the shifts per day so the power arrangement can be sized properly.
Measure the pallet footprint and the heaviest single load before comparing models.
On the TFY100D, mark the stations where loads are picked up and dropped off each shift.
Check the lowest door, beam height and aisle the truck has to pass through.
On the TFY100D, note any slope, threshold or step along the working route.
On the TFY100D, loads are kept low while travelling between stations.
Battery or fuel levels are checked at the start of each shift.
On the TFY100D, unusual noise or movement is reported before further use.
Routine checks cover tyres, brakes, controls and visible leaks.
On the TFY100D, the layout drawing shows where each machine sits in the operation.
Storage cages and racking organise the loads it moves between stations.
On the TFY100D, a mixed enquiry can list this model together with other families.
This machine usually works alongside pallet trucks and stacking equipment.
On the TFY100D, dimensions are checked against the source record before quoting.
Site conditions such as gradient, dust and moisture belong in the enquiry.
On the TFY100D, the specification sheet is the binding reference for listed values.
The signed datasheet issued with the quotation is the binding version.
On the TFY100D, the operation and parts material travel with the machine.
The enquiry should include the quantity and destination port.
On the TFY100D, loading is recorded before the container is sealed.
Packing follows sea-freight practice for the chosen chassis.
The operation material covers controls, checks and routine service points.
Test and conformity documents follow the model and destination market.
The serial number identifies the build when parts are ordered later.
Questions
The listed rated capacity is 1000Kg at the standard load centre. Above the rated lift height capacity derates along the mast curve.
The listed service or net weight is 170 kg. This matters for floor loading, ramps and container plans.
Container entry depends on lowered width, mast height and guard clearance. Compare these with the container door.
The product range is CE marked and the factory holds ISO 9001, ISO 14001 and ISO 18001. The documents issued for a specific order are listed in the quotation.
Many forklift, pallet truck, stacker and reach truck models are held in ready stock; customised units are built in about 25 days. The confirmed date for your order is stated on the proforma invoice.
The machine ships with a parts manual. Wear parts can be ordered after delivery against serial number and part name.
Send load per move, lift height, floor surface, quantity and destination port. The reply lists the matching specification.
Prices are not published. Price follows chassis, mast or lift option, power arrangement, tyres and destination port; send the specification and you receive a line-by-line offer.
The minimum order quantity is one set, and mixed models can be combined in one container.
Related
Same-family comparison using the published source figures; open a model page for the full specification.
LPG and gas forklift trucks related models
Explore
Send the load per move, the lift height and the floor surface. The sales desk matches the chassis to those figures and replies with a line-by-line offer.